II. Preparation of Material.
The method employed in the preparation of paranitroorthosulphobenzoic acid was essentially that described by Hart,[7]Kastle,[8]Gray[9]and Hollis.[10]The details of it are repeated here for the purpose of calling attention to certain facts that came under the author’s notice.
100 grams of paranitrotoluene are added to 400 grams of fuming sulfuric acid, and the mixture heated in a balloon flask at 100° on a water bath. The heating is continued until a few drops of the mixture, added to cold water, dissolves completely to a clear solution. The timerequired for this operation varies much with the conditions. Continued stirring very considerably hastens the reaction, as paranitrotoluene forms a layer on the acid, which presents a small surface to its action. With constant stirring the reaction is complete in a few hours, whereas if no stirring is resorted to, as much as several days may be required, especially when large quantities are employed at one time.
When the reaction is complete, the mixture is poured into a large volume of water, and neutralized with calcium carbonate. In the filtrate from calcium sulphate, the calcium salt of paranitroorthotoluene sulphonic acid is found, and this is converted into the potassium salt in the usual way.
The oxidation of the potassium salt is effected as follows. 50 grams of the salt are dissolved in 2½ litres of water, and to this is added a solution of 15 grams of potassium hydroxide. The mixture is heated to 100° on a water-bath, and when this temperature is reached, 110 grams of potassium permanganate are added. Heating is continued until the solution is decolorized, care being taken to prevent the evolution of free oxygen.
The oxides of manganese are then filtered off, the filtrate neutralized with hydrochloric acid, and evaporated to about one fifth of its original volume. Strong hydrochloric acid is them added in excess, and on cooling the acid potassium salt of paranitroorthosulphobenzoic acid separates in very slender colorless needles completely filling the liquid.
For the success of this operation it is important that the potassium salt of paranitroorthotoluenesulphonic acid and the potassium hydroxide should both be perfectly dissolved before they are heated together. If the two substances lie together in solid form at the bottom of the flask, a very slight elevation of temperature leads to the formation of an extremely troublesome red substance, which is very difficult to remove. It is almost impossible to remove it from the oxidation product by recrystallization, since any considerable amount of it has a marked influence on the solubility of the salt, rendering it much more soluble. It persists throughout all subsequent transformations of paranitroorthosulphobenzoic acid, and should therefore be carefully avoided.
Otto Fischer[11]has shown that in concentrated solution, potassium hydroxide acts on nitro derivatives of toluene, with the formation of various colored substances derived from stilbene. In the case of paranitroorthotoluenesulphonic acid, he describes the substance formed as possessing a cherry red color. The reactions involved in its formation are:
CH₃HC ============== CH//\2C₆H₃—SO₂OK = C₆H₃—SO₂OK KO.O₂S—C₆H₃ + 2H₂O\\/NO₂\/\/— O — \/NN\— O — /
By oxidation this passes to a nitro compound of the composition
HC ============= CH/\C₆H₃—SO₂OK KOO₂S—C₆H₃\/NO₂O₂N
It was no doubt the formation of substances of this nature that occasioned the color observed in some of the oxidations.
The only effective method of separating this colored substance was found to be to pass to the neutral salt of paranitroorthosulphobenzoic acid, by making the solution slightly alkaline. The salt of this colored substance is also formed and the two can be separated by a few recrystallizations in a fairly satisfactory manner.
The yield in both of the transformations involved in the preparation of paranitroorthosulphobenzoic acid does not fall far short of the theoretical.