CHAPTERLXXX.HINTS, ON THE CHEAPEST METHOD OF INFLATING BALLOONS, WITH DESCRIPTIONS OF DIFFERENT MODELS FOR A GASS-STEAM-ENGINE.Section 429.THEExpenceattending the Inflation of Balloons is a solid Objection to their frequent Use.A Check is thereby given to every Improvement that might otherwise be expected from a Repetition of Experiments.It is, in short, the chief Difficulty under which theaironautic artat present labours.This Difficulty, however, if once overcome, (and of which there is little Doubt) will probably bring those extraordinary Machines, into general Estimation.Whatnowcosts fifty Pounds, maythenbe done for five: abating the Expence of the preparatory Engine.Mons. Lavoisier, by the Application of Steam to Iron Filings enclosed in a Copper Retort, hasgenerated inflammable Air, or light Gass:[136]and Dr. Priestley, by converting a Gun-Barrel into a Steam-Engine, has produced a Gass 13 Times lighter than common Air;[137]whereas by the present expensive Method, with Metal and Acid, the Gass for Inflation is seldom more than six Times lighter.What has hitherto been atchieved on a small Scale, is here meant to be extended.As no Particulars are made public, or at least, have yet come to the Author’s Knowledge, relative to the Construction of such a Gass-Steam-Engine, as may, with Safety and Effect, be applied to the Inflation of Balloons; the following Descriptions of different Models may deserve some Notice:—may possibly excite the Attention of the ingenious; and put them on contrivingeasierMeans to obtain thesameEnd.I.430. Let there be an IronHot-hearth, one Yard square, and two Inches thick. Let it beseton a Common Brick Stove, built as near the Ground as possible, (or even below it) in the open Air. Its Chimney to consist of malleable Iron, flat at the Top, and strong enough to support a Tea-Kettle or Boiler to produce Steam: and extending at least one Yard from the End of the Hearth horizontally, before it turns up. It may rise three or four Yards high, slanting farther from the Hearth: the Form a hollow Cylinder: with a Turn-Cap at the Top, two Feet long,set on at right Angles; for the Management of the Smoke.Supposing then the Fire-Place to face the West; the Chimney may project Eastward. The North Side is to be appropriated to the Iron-Borings or Turnings; and on the South Side is to be deposited the Dross or Calx.A Muffle or Mould of malleable Iron is to be screwed and luted over the hot Hearth. The four Sides of the Muffle next the Hearth are to have horizontal Lips or Rims projecting half an Inch: and Screws are to be driven, throu’ Holes drilled at proper Distances, into the Hearth. The Sides are to rise upright a Couple of Inches: closing, as they rise, in the Form of a hollow Cylinder, one Foot in Diameter, and perhaps a Yard above the Hearth: which is now converted into aGass-Steam-Engine.It is proposed to strew over theHot-heartha thin Layer of Borings, one Tenth of an Inch thick; to which Layer whenredhot, the boiling Steam is to be applied. The extricated Gass is to be conveyed from the Top of the Cylinder, by Means of an extended Trunk of Tin, and varnished Linen, into a Tub of cold Water keptcontinuallyflowing over, into which a few Lumps of quick Lime are thrown: and from thence the Gass is to rise into the Balloon.431. The Iron, whether Filings or Turnings, proper for Inflation, must bebright; wholly free from Chips, Bits of Wood, and all heterogeneous Particles: but particularly RUST, and GREASE:lessthan a cubic Inch of the latter, woud spoil a Ton of the brightest, and otherwise the best prepared Materials. (Section 339.)A Day or twoonly, before a Balloon is inflated; the proper Quantity of bright Iron shoud be heatedred hotinCharcoal, and suffered to go cold.For Want of this simple Preparation of the Iron, the Gass has proved defective in Point oflevity: altho’ the Balloon appeared fully inflated.This Misfortune happened at Birmingham, and other Places.432. TheDesideratumis,quicklyto apply, andremovethe Borings, keeping the MachinenearlyAir-tight. For, it is now well known, that the Gass willexplode, if one-third Part of common Air be introduced: or, if less; it mayunitewith theGass, and detract fromitsLevity.433. The followingParticularsmay likewise be considered as an Improvement.II.1. To lay a Plate of Iron, Brass, or Copper, over the Hearth; which, if made ofcastIron, will be apt to crack, in Contact with the Steam; and will also unite with and concrete the Iron Turnings or Gun-Borings into a solid Mass, that woud be separated with Difficulty.2. To make the Dross-Pit in the Form of a hollow Wedge, narrow at the Top: screwing and luting it to the South Side of the Hearth. It shoud hold the Dross arising from a Ton of Borings; which will be sufficient for the Inflation of a Balloon, to carry one Person.3. On the North Side is to be erected a Platform of Brick, a Yard square,flooredwith a Plate of Iron: the inside Surface to be even with the Bottom of the Hearth.4. The Ton of Borings is to be placed on theFloor, and covered with another Muffle, secured and luted to the Side of the Hearth: having a Communication of two Inches high, and one Yard wide, with the Bottom of the Hearth: as the Dross-Pit has.5. A Brass or Copper Rake is to remain within the two Muffles: to press forward the Borings, spread them over the Hearth; stir them frequently;—by turning the Instrument, scrape them into the Dross-Pit; and apply fresh from theDeposit.6. To perform these manual Operations within the Machine kept Air-tight; it will be necessary, at the exterior End of the Muffle, to fasten a strong leathern Case, made very wide and pliant, and two Yards long: into which the End of the Rake-Handle is to be inserted.III.434.The Mode of Operation.The Borings being spread on the Hearth, andredhot; the Steam Pipe is to be opened, andinstantlyshut. The Gass beingsuddenlyextricated; the Pipe is to be opened, and shut again as before: the Borings pushed into the Dross-Pit, and a fresh Supply spread. This Process to be renewed, till the Inflation is completed.If it be thought necessary to prevent the Steam from communicating with the whole Depôt of Borings, and so evolve too much Gass; a little Brass Door with Hinges of the same, might be made to hang from the Top of the Communication between the two Muffles: which Door opening inwards, and hanging vertically,woud by the Pressure of the Gass, stop up the Open: and yet, if made strong,notprevent the Operations of the Rake, at proper Times.IIII.435. The Machine woud be less complex, with one large Muffle, somewhat longer North and South than the Hearth; furnished with leathern Case and Rake. Put in the Borings at one End: keep the Steam-Pipe always open; with aHandat the Rake; pushing away the Dross, and pressing forwards fresh Borings.V.436. Further: it has since occurred, that a Machine in the Form of agun-barrel,extended in all its Dimensions, will probably answereveryIntention.And of this Kind are the hollow cylindrical Tubes, ofdifferentLengths, and about a Foot in Diameter,[138]which arecast, for the Conveyance of Steam, from the Boiler of a Steam-Engine.Such a one, (previously lined with a Cylinder of Copper, or malleable Iron, to prevent the Adhesion of the Borings, when reduced to a Calx by the Admission of Steam;) might be placed horizontally over a Stove, (with or without a Chimney) and surrounded withredhot Coals.The Ton of Borings might be deposited at one End of the Tube; and, by Means of the Air-tight flexible leathern Case, be pressed with a Rake,graduallyinto the Fire, andbeyondit when calcined.Care must be taken to make theApparatusnearly Air-tight.The Steam shoud pass into the Tube, frombelow: and the Gass be conducted towards the Balloon throu’ another Iron Cylinder, nearly equal in Diameter and at right Angles with the first; lying also in an horizontal Direction; along the Ground.The Tubes might beforgedorcast, so as to form but one rectangular Piece.The further End of the second Tube shoud communicate with athird, made of Tin, and bent downwards about a Foot; thence at right Angles, for six Inches: then to rise up, also at right Angles, the Length of six Inches more.The Tin Tube is to descend into a Cistern of cold Water, made to flow over continually, by a fresh Supply; and into which, a few Lumps of Quicklime shoud be thrown.The Gass, which will press upwards throu’ the Water, is to be received into an inverted Funnel, and thence (as in Section 339, Art. 2.) conveyed to the Balloon.VI.437. The following Alterations woud supersede the Use of the Rake, andleathernCases: the latter of which, by any accidental Crack or Flaw in the Leather, might admit a sufficient Quantity of common Air to produce an Explosion.The cylindric Form of the Copper, or malleable Iron (to be used as a Lining for the Tube) is to be changed, into that of a half Cylinder, or inverted Muffle: and to be perforated with small Holes.This Muffle is to benearlyfilled with a Ton of Iron Borings: (the Ends to be made up, to prevent the Borings from falling out into theTube;) the Muffle itself is to be supported by a Cradle[139]of the same Form, made ofstrongCopper Wire,[140]like theopenIron-Wire-Fenders: and the whole is to be thrust into the Tube.The Length of the Muffle depends on the Quantity of Borings that are intended to be used.The Ends of the Tube shoud not be made so strong as the Tube itself: that, if an Explosion happens, theymaygive way first, and prevent a Rupture of the Tube: not that any Danger is to be apprehended, that such an Event will take Place, so long as the Steam-Pipe is attended to, by a proper Person: the above Caution being only given, to prevent a Possibility of Rupture.Each End shoud be cast, or forged with a hollow Handle; and shoud screw into the Tube.The Length of the Tube shoud be such, that the Person who attends the Steam-Pipe, shoud feel no Inconvenience from the Heat of the Fire.Nine Feet woud therefore be a proper Length: the conducting Tube the same.Within six Inches from each End of the Tube which holds the Borings, a Hole, half an Inch in Diameter shoud be drilled across the Middle of the Tube, in an horizontal Direction.Into these, an Iron Axis is to be fitted, (so as to take outoccasionally) and pass throu’ the Tube: each End of the Axis is to project outwards a Couple of Inches, and to be madesquare, for the Socket of a strong Iron Winch or Handle.Each Axis to be furnished with a strong Chain, of equal Length with the Tube; one End of which Chain is to be riveted, or otherwise fixed, to the Middle of the Axis; and the other, to be fastenedoccasionallyto one Extremity of the Cradle and Muffle: the second Axis and Chain in like Manner, to the other Extremity.The Muffle is to be placed in the Cradle: both are then to be thrust into the Tube, and fastened to the Chain at the farther Axis: in which Position the Muffle may be filled with Borings, and gradually drawn into the Tube; till the same End has reached the Center of the Fire. The nearer End is then to be hooked by the nearer Chain, already wrapped round the nearer Axis: and the light Iron Caps to be screwed on each End of the Tube.438. The Boiler for Steam may be fixed on any Part of the Tube near the Fire, and near the opposite Axis; so that one Person may attend both the Steam-Pipe, and Axis. The Steam to be conveyed throu’ a small Orifice made in the Bottom of the Tube, between the same Axis and the Fire.439. As soon as the Materials, above the Center of the Fire, are supposed to beredhot, the Steam-Pipe is to be opened for a Moment andshut again. The extricated Gass will be instantlyheard, rushing throu’ the Vessel ofcoldWater; and as instantlyseento swell the varnished Linen-Trunk as it passes into the Balloon.The Steam-Pipe is to be regulated by these infallible Signals: and the Process continued, till that Quantity of Borings, that was in theCenter of the Fire, and consequentlyredhot, is supposed to be calcined.At which Time, the Handles are to be applied to the Axis, and the Cradle and Muffle drawn 5 or 6 Inches forward into the Fire.When drawn too far; Recourse must be had to the second Axis.440. If great Expedition is required, two or three Conductors from the same Tube may be used: and, at the Distance of six or seven Feet from the Fire,Tin-Conductorsmay be added; taking Care that they aremade,applied, andcontinued Air-tight.THE END.
CHAPTERLXXX.
Section 429.THEExpenceattending the Inflation of Balloons is a solid Objection to their frequent Use.
A Check is thereby given to every Improvement that might otherwise be expected from a Repetition of Experiments.
It is, in short, the chief Difficulty under which theaironautic artat present labours.
This Difficulty, however, if once overcome, (and of which there is little Doubt) will probably bring those extraordinary Machines, into general Estimation.
Whatnowcosts fifty Pounds, maythenbe done for five: abating the Expence of the preparatory Engine.
Mons. Lavoisier, by the Application of Steam to Iron Filings enclosed in a Copper Retort, hasgenerated inflammable Air, or light Gass:[136]and Dr. Priestley, by converting a Gun-Barrel into a Steam-Engine, has produced a Gass 13 Times lighter than common Air;[137]whereas by the present expensive Method, with Metal and Acid, the Gass for Inflation is seldom more than six Times lighter.
What has hitherto been atchieved on a small Scale, is here meant to be extended.
As no Particulars are made public, or at least, have yet come to the Author’s Knowledge, relative to the Construction of such a Gass-Steam-Engine, as may, with Safety and Effect, be applied to the Inflation of Balloons; the following Descriptions of different Models may deserve some Notice:—may possibly excite the Attention of the ingenious; and put them on contrivingeasierMeans to obtain thesameEnd.
430. Let there be an IronHot-hearth, one Yard square, and two Inches thick. Let it beseton a Common Brick Stove, built as near the Ground as possible, (or even below it) in the open Air. Its Chimney to consist of malleable Iron, flat at the Top, and strong enough to support a Tea-Kettle or Boiler to produce Steam: and extending at least one Yard from the End of the Hearth horizontally, before it turns up. It may rise three or four Yards high, slanting farther from the Hearth: the Form a hollow Cylinder: with a Turn-Cap at the Top, two Feet long,set on at right Angles; for the Management of the Smoke.
Supposing then the Fire-Place to face the West; the Chimney may project Eastward. The North Side is to be appropriated to the Iron-Borings or Turnings; and on the South Side is to be deposited the Dross or Calx.
A Muffle or Mould of malleable Iron is to be screwed and luted over the hot Hearth. The four Sides of the Muffle next the Hearth are to have horizontal Lips or Rims projecting half an Inch: and Screws are to be driven, throu’ Holes drilled at proper Distances, into the Hearth. The Sides are to rise upright a Couple of Inches: closing, as they rise, in the Form of a hollow Cylinder, one Foot in Diameter, and perhaps a Yard above the Hearth: which is now converted into aGass-Steam-Engine.
It is proposed to strew over theHot-heartha thin Layer of Borings, one Tenth of an Inch thick; to which Layer whenredhot, the boiling Steam is to be applied. The extricated Gass is to be conveyed from the Top of the Cylinder, by Means of an extended Trunk of Tin, and varnished Linen, into a Tub of cold Water keptcontinuallyflowing over, into which a few Lumps of quick Lime are thrown: and from thence the Gass is to rise into the Balloon.
431. The Iron, whether Filings or Turnings, proper for Inflation, must bebright; wholly free from Chips, Bits of Wood, and all heterogeneous Particles: but particularly RUST, and GREASE:lessthan a cubic Inch of the latter, woud spoil a Ton of the brightest, and otherwise the best prepared Materials. (Section 339.)
A Day or twoonly, before a Balloon is inflated; the proper Quantity of bright Iron shoud be heatedred hotinCharcoal, and suffered to go cold.
For Want of this simple Preparation of the Iron, the Gass has proved defective in Point oflevity: altho’ the Balloon appeared fully inflated.
This Misfortune happened at Birmingham, and other Places.
432. TheDesideratumis,quicklyto apply, andremovethe Borings, keeping the MachinenearlyAir-tight. For, it is now well known, that the Gass willexplode, if one-third Part of common Air be introduced: or, if less; it mayunitewith theGass, and detract fromitsLevity.
433. The followingParticularsmay likewise be considered as an Improvement.
1. To lay a Plate of Iron, Brass, or Copper, over the Hearth; which, if made ofcastIron, will be apt to crack, in Contact with the Steam; and will also unite with and concrete the Iron Turnings or Gun-Borings into a solid Mass, that woud be separated with Difficulty.
2. To make the Dross-Pit in the Form of a hollow Wedge, narrow at the Top: screwing and luting it to the South Side of the Hearth. It shoud hold the Dross arising from a Ton of Borings; which will be sufficient for the Inflation of a Balloon, to carry one Person.
3. On the North Side is to be erected a Platform of Brick, a Yard square,flooredwith a Plate of Iron: the inside Surface to be even with the Bottom of the Hearth.
4. The Ton of Borings is to be placed on theFloor, and covered with another Muffle, secured and luted to the Side of the Hearth: having a Communication of two Inches high, and one Yard wide, with the Bottom of the Hearth: as the Dross-Pit has.
5. A Brass or Copper Rake is to remain within the two Muffles: to press forward the Borings, spread them over the Hearth; stir them frequently;—by turning the Instrument, scrape them into the Dross-Pit; and apply fresh from theDeposit.
6. To perform these manual Operations within the Machine kept Air-tight; it will be necessary, at the exterior End of the Muffle, to fasten a strong leathern Case, made very wide and pliant, and two Yards long: into which the End of the Rake-Handle is to be inserted.
434.The Mode of Operation.
The Borings being spread on the Hearth, andredhot; the Steam Pipe is to be opened, andinstantlyshut. The Gass beingsuddenlyextricated; the Pipe is to be opened, and shut again as before: the Borings pushed into the Dross-Pit, and a fresh Supply spread. This Process to be renewed, till the Inflation is completed.
If it be thought necessary to prevent the Steam from communicating with the whole Depôt of Borings, and so evolve too much Gass; a little Brass Door with Hinges of the same, might be made to hang from the Top of the Communication between the two Muffles: which Door opening inwards, and hanging vertically,woud by the Pressure of the Gass, stop up the Open: and yet, if made strong,notprevent the Operations of the Rake, at proper Times.
435. The Machine woud be less complex, with one large Muffle, somewhat longer North and South than the Hearth; furnished with leathern Case and Rake. Put in the Borings at one End: keep the Steam-Pipe always open; with aHandat the Rake; pushing away the Dross, and pressing forwards fresh Borings.
436. Further: it has since occurred, that a Machine in the Form of agun-barrel,extended in all its Dimensions, will probably answereveryIntention.
And of this Kind are the hollow cylindrical Tubes, ofdifferentLengths, and about a Foot in Diameter,[138]which arecast, for the Conveyance of Steam, from the Boiler of a Steam-Engine.
Such a one, (previously lined with a Cylinder of Copper, or malleable Iron, to prevent the Adhesion of the Borings, when reduced to a Calx by the Admission of Steam;) might be placed horizontally over a Stove, (with or without a Chimney) and surrounded withredhot Coals.
The Ton of Borings might be deposited at one End of the Tube; and, by Means of the Air-tight flexible leathern Case, be pressed with a Rake,graduallyinto the Fire, andbeyondit when calcined.
Care must be taken to make theApparatusnearly Air-tight.
The Steam shoud pass into the Tube, frombelow: and the Gass be conducted towards the Balloon throu’ another Iron Cylinder, nearly equal in Diameter and at right Angles with the first; lying also in an horizontal Direction; along the Ground.
The Tubes might beforgedorcast, so as to form but one rectangular Piece.
The further End of the second Tube shoud communicate with athird, made of Tin, and bent downwards about a Foot; thence at right Angles, for six Inches: then to rise up, also at right Angles, the Length of six Inches more.
The Tin Tube is to descend into a Cistern of cold Water, made to flow over continually, by a fresh Supply; and into which, a few Lumps of Quicklime shoud be thrown.
The Gass, which will press upwards throu’ the Water, is to be received into an inverted Funnel, and thence (as in Section 339, Art. 2.) conveyed to the Balloon.
437. The following Alterations woud supersede the Use of the Rake, andleathernCases: the latter of which, by any accidental Crack or Flaw in the Leather, might admit a sufficient Quantity of common Air to produce an Explosion.
The cylindric Form of the Copper, or malleable Iron (to be used as a Lining for the Tube) is to be changed, into that of a half Cylinder, or inverted Muffle: and to be perforated with small Holes.
This Muffle is to benearlyfilled with a Ton of Iron Borings: (the Ends to be made up, to prevent the Borings from falling out into theTube;) the Muffle itself is to be supported by a Cradle[139]of the same Form, made ofstrongCopper Wire,[140]like theopenIron-Wire-Fenders: and the whole is to be thrust into the Tube.
The Length of the Muffle depends on the Quantity of Borings that are intended to be used.
The Ends of the Tube shoud not be made so strong as the Tube itself: that, if an Explosion happens, theymaygive way first, and prevent a Rupture of the Tube: not that any Danger is to be apprehended, that such an Event will take Place, so long as the Steam-Pipe is attended to, by a proper Person: the above Caution being only given, to prevent a Possibility of Rupture.
Each End shoud be cast, or forged with a hollow Handle; and shoud screw into the Tube.
The Length of the Tube shoud be such, that the Person who attends the Steam-Pipe, shoud feel no Inconvenience from the Heat of the Fire.
Nine Feet woud therefore be a proper Length: the conducting Tube the same.
Within six Inches from each End of the Tube which holds the Borings, a Hole, half an Inch in Diameter shoud be drilled across the Middle of the Tube, in an horizontal Direction.
Into these, an Iron Axis is to be fitted, (so as to take outoccasionally) and pass throu’ the Tube: each End of the Axis is to project outwards a Couple of Inches, and to be madesquare, for the Socket of a strong Iron Winch or Handle.
Each Axis to be furnished with a strong Chain, of equal Length with the Tube; one End of which Chain is to be riveted, or otherwise fixed, to the Middle of the Axis; and the other, to be fastenedoccasionallyto one Extremity of the Cradle and Muffle: the second Axis and Chain in like Manner, to the other Extremity.
The Muffle is to be placed in the Cradle: both are then to be thrust into the Tube, and fastened to the Chain at the farther Axis: in which Position the Muffle may be filled with Borings, and gradually drawn into the Tube; till the same End has reached the Center of the Fire. The nearer End is then to be hooked by the nearer Chain, already wrapped round the nearer Axis: and the light Iron Caps to be screwed on each End of the Tube.
438. The Boiler for Steam may be fixed on any Part of the Tube near the Fire, and near the opposite Axis; so that one Person may attend both the Steam-Pipe, and Axis. The Steam to be conveyed throu’ a small Orifice made in the Bottom of the Tube, between the same Axis and the Fire.
439. As soon as the Materials, above the Center of the Fire, are supposed to beredhot, the Steam-Pipe is to be opened for a Moment andshut again. The extricated Gass will be instantlyheard, rushing throu’ the Vessel ofcoldWater; and as instantlyseento swell the varnished Linen-Trunk as it passes into the Balloon.
The Steam-Pipe is to be regulated by these infallible Signals: and the Process continued, till that Quantity of Borings, that was in theCenter of the Fire, and consequentlyredhot, is supposed to be calcined.
At which Time, the Handles are to be applied to the Axis, and the Cradle and Muffle drawn 5 or 6 Inches forward into the Fire.
When drawn too far; Recourse must be had to the second Axis.
440. If great Expedition is required, two or three Conductors from the same Tube may be used: and, at the Distance of six or seven Feet from the Fire,Tin-Conductorsmay be added; taking Care that they aremade,applied, andcontinued Air-tight.
THE END.