See Russell N. Bellows,Henry Whitney Bellows(Keene, N.H., 1897), a biographical sketch reprinted from T.B. Peck’sBellows Family Genealogy; John White Chadwick,Henry W. Bellows: His Life and Character(New York, 1882), a memorial address; and Charles J Stillé,History of the United States Sanitary Commission(Philadelphia, 1866).
See Russell N. Bellows,Henry Whitney Bellows(Keene, N.H., 1897), a biographical sketch reprinted from T.B. Peck’sBellows Family Genealogy; John White Chadwick,Henry W. Bellows: His Life and Character(New York, 1882), a memorial address; and Charles J Stillé,History of the United States Sanitary Commission(Philadelphia, 1866).
BELLOWSandBLOWING MACHINES,appliances used for producing currents of air, or for moving volumes of air from one place to another. Formerly all such artificially-produced currents of air were used to assist the combustion of fires and furnaces, but now this purpose only forms a part of the uses to which they are put. Blowing appliances, among which are included bellows, rotary fans, blowing engines, rotary blowers and steam-jet blowers, are now also employed for forcing pure air into buildings and mines for purposes of ventilation, for withdrawing vitiated air for the same reason, and for supplying the air or other gas which is required in some chemical processes. Appliances of this kind differ fromair compressorsin that they are primarily intended for the transfer of quantities of air at low pressures, very little above that of the atmosphere, whereas the latter are used for supplying air which has previously been raised to a pressure which may be many times that of the atmosphere (seePower Transmission:Pneumatic).
Among the earliest contrivances employed for producing the movement of air under a small pressure were those used in Egypt during the Greek occupation. These depended upon the heating of the air, which, being raised in pressure and bulk, was made to force water out of closed vessels, the water being afterwards employed for moving some kind of mechanism. In the process of iron smelting there is still used in some parts of India an artificial blast, produced by a simple form of bellows made from the skins of goats; bellows of this kind probably represent one of the earliest contrivances used for producing currents of air.
Thebellows1now in use consists, in its simplest form, of two flat boards, of rectangular, circular or pear shape, connected round their edges by a wide band of leather so as to include an air chamber, which can be increased or diminished in volume by separating the boards or bringing them nearer together. The leather is kept from collapsing, on the separation of the boards, by several rings of wire which act like the ribs of animals. The lower board has a hole in the centre, covered inside by a leather flap or valve which can only open inwards; there is also an open outlet, generally in the form of a pipe or nozzle, whose aperture is much smaller than that of the valve. When the upper board is raised air rushes into the cavity through the valve to fill up the partial vacuum produced; on again depressing the upper board the valve is closed by the air attempting to rush out again, and this air is discharged through the open nozzle with a velocity depending on the pressure exerted.
The current of air produced is evidently not continuous but intermittent or in puffs, because an interval is needed to refill the cavity after each discharge. In order to remedy this drawback thedouble bellowsare used. To understand their action it is only necessary to conceive an additional board with valve, like the lower board of the single bellows, attached in the same way by leather below this lower board. Thus there are three boards, forming two cavities, the two lower boards being fitted with air-valves. The lowest board is held down by a weight and another weight rests on the top board. In working these double bellows the lowest board is raised, and drives the air from the lower cavity into the upper. On lowering the bottom board again a fresh supply of air is drawn in through the bottom valve, to be again discharged when the board is raised. As the air passes from the lower to the upper cavity it is prevented from returning by the valve in the middle board, and in this way a quantity of air is sent into the upper cavity each time the lowest board is raised. The weight on the top board provides the necessary pressure for the blast, and at the same time causes the current of air delivered to be fairly continuous. When the air is being forced into the upper cavity the weight is beingraised, and, during the interval when the lowest board is descending, the weight is slowly forcing the top board down and thus keeping up the flow of air.
Hand-bellows for domestic use are generally shaped like a pear, with the hinge at the narrow end. The same shape was adopted for the older forms of smiths’ bellows, with the difference that two bellows were used superposed, in a manner similar to that just described, so as to provide for a continuous blast. In the later form of smiths’ bellows the same principle is employed, but the boards are made circular in shape and are always maintained roughly parallel to one another. These are shown on figs. 1 and 2. Here A is the blast pipe, B the movable lowest board, C the fixed middle board, close to which the pipe A is inserted, and D is the movable uppermost board pressed upon by the weight shown. The board B is raised by means of a hand lever L, through either a chain or a connecting rod, and lowered by a weight. The size of the weight on D depends on the air pressure required. For instance, if a blast pressure of half a pound per square inch is wanted and the boards are 18 in. in diameter, and therefore have an area of 254 sq. in., on each of the 254 sq. in. there is to be a pressure of half a pound, so that the weight to balance this must be half multiplied by 254, or 127 ℔ The diameter of the air-pipe can be varied to suit the required conditions. Instead of bellows with flexible sides, a sliding arrangement is sometimes used; this consists of what are really two boxes fitting into one another with the open sides both facing inwards, as if one were acting as a lid to the other. By having a valve and outlet pipe fitted as in the bellows and sliding them alternately apart and together, an intermittent blast is produced. The chief defect of this arrangement is the leakage of air caused by the difficulty in making the joint a sufficiently good fit to be air-tight.
Blowing Engines.—Where larger quantities of air at higher pressures than can conveniently be supplied by bellows are required, as for blast furnaces and the Bessemer process of steel-making, what are termed “blowing engines” are used. The mode of action of a blowing engine is simple. When a piston, accurately fitting a cylinder which has one end closed, is forcibly moved towards the other end, a partial vacuum is formed between the piston and the blank end, and if this space be allowed to communicate with the outer atmosphere air will flow in to fill the vacuum. When the piston has completed its movement or “stroke,” the cylinder will have been filled with air. On the return of the piston, if the valve through which the air entered is now closed and a second one communicating with a chamber or pipe is opened, the air in the cylinder is expelled through this second valve. The action is similar to that of the bellows, but is carried out in a machine which is much better able to resist higher pressures and which is more convenient for dealing with large quantities of air. The valves through which the atmosphere or “free” air is admitted are called “admission” or “suction” valves, and those through which the air is driven from the cylinder are the “discharge” or “delivery” valves. Formerly one side only of the blowing piston was used, the engine working “single-acting”; but now both sides of the piston are utilized, so that when it is moving in either direction suction will be taking place on one side and delivery on the other. All processes in connexion with which blowing engines are used require the air to be above the pressure of the outer atmosphere. This means that the discharge valves do not open quite at the beginning of the delivery stroke, but remain closed until the air in the cylinder has been reduced in volume and so increased in pressure to that of the air in the discharge chamber.
The power used to actuate these blowing-engines is in most cases steam, the steam cylinder being placed in line or “tandem” with the air cylinder, so that the steam piston rod is continuous with or directly joined to the piston rod of the air cylinder. This plan is always adopted where the cylinders are placed horizontally, and often in the case of vertical engines. The engines are generally built in pairs, with two blowing cylinders and one high-pressure and one low-pressure steam cylinder, the piston rods terminating in connecting rods which are attached to the pins of the two cranks on the shaft. In the centre of this shaft, midway between the two engines, there is usually placed a heavy flywheel which helps to maintain a uniform speed of turning. Some of the largest blowing engines built in Great Britain are arranged as beam engines; that is to say, there is a heavy rocking beam of cast iron which in its middle position is horizontal. One end of this beam is linked by a short connecting rod to the end of the piston rod of the blowing cylinder, while the other end is similarly linked to the top of the steam piston rod, so that as the steam piston comes up the air piston goes down andvice versa. At the steam end of the beam a third connecting rod works the crank of a flywheel shaft.
About the end of the 19th century an important development took place which consisted in using the waste gas from blast furnaces to form with air an explosive mixture, and employing this mixture to drive the piston of the actuating cylinder in precisely the same manner as the explosive mixture of coal gas and air is used in a gas engine. Since the majority of blowing engines are used for providing the air required in iron blast furnaces, considerable saving should be effected in this way, because the gas which escapes from the top of the furnace is a waste product and costs nothing to produce.
The general action of a blowing engine may be illustrated by the sectional view shown on fig. 3, which represents the internal view of one of the blowing cylinders of the engines erected at the Dowlais Ironworks as far back as 1851. Many of the details are now obsolete, but the general scheme is the same as in all blowing engines. Here A is the air cylinder; in this is a piston whose rod is marked R; this piston is usually made air-tight by some form of packing fitted into the groove which runs round its edge. In this particular case the cylinder is placed vertically and its piston rod is actuated from the end of a rocking beam. The top and bottom ends are closed by covers and in theseare a number of openings controlled by valves opening inwards so that air can flow freely in but cannot return. The piston is shown moving downwards. Air is now being drawn into the space above the piston through the valves v at the top, and the air in the space A below the piston, drawn in during the previous up-stroke, is being expelled through the valve v′ into the discharge chamber B, thence passing to the outlet pipe O. The action is reversed on the up-stroke. Thus it will be seen that air is being delivered both during the up-stroke and the down-stroke, and therefore flows almost continuously to the furnaces. There must, however, be momentary pauses at the ends of the strokes when the direction of movement is changed, and as the piston, though worked from an evenly rotating crank shaft, moves more quickly at the middle and slows down to no speed at the ends of its travel, there must be a considerable variation in the speed of delivery of the air. The air is therefore led from O into a large storage chamber or reservoir, whence it is again taken to the furnace; if this reservoir is made sufficiently large the elasticity of the air in it will serve to compensate for the irregularities, and a nearly uniform stream of air will flow from it. The valves used in this case and in most of the older blowing engines consist of rectangular metal plates hinged at one of the longer edges; these plates are faced with leather or india rubber so as to allow them to come to rest quietly and without clatter and at the same time to make them air-tight. It will be seen that some of these valves hang vertically and others lie flat on the bottom of the cover. The Dowlais cylinder is very large, having a diameter of 12 ft. and a piston stroke of 12 ft., giving a discharge of 44,000 cub. ft. of air per minute, at a pressure of 4¼ ℔ to the square inch.
A later design of blowing engine, built in 1871 for the Lackenby iron-works, Middlesbrough, is shown in section in fig. 4, and is of a type which is still the most common, especially in the north of England. Here A, the high-pressure steam cylinder, and C, the low-pressure one, are placed in tandem with the air cylinders B, B, whose pistons they actuate. In these blowing cylinders the inlet valves in the bottom are circular disk valves of leather, eighteen in number; the inlet valves T on the top of the cylinder are arranged in ten rectangular boxes, having openings in their vertical sides, inside which are hung leather flap valves. The outlet valves O are ten in number at each end of the cylinders, and are hung against flat gratings which are arranged round the circumference. The blast is delivered into a wrought iron casing M which surrounds the cylinder. The combined area of the inlet valves is 860 sq. in., or one-sixth the area of the piston. The speed is twenty-four revolutions per minute and the air delivered at this speed is 15,072 cubic ft. per minute, the horse-power in the air cylinders being 258. The circulating pump E, air pump F, and feed pumps G, G, are worked off the cross-head on the low-pressure side.
A more modern form of blowing engine erected at the Dowlais works about the end of the 19th century, may be taken as typical of the present design of vertical blowing engine in use in Great Britain. The two air cylinders are placed below and in tandem with the steam cylinders as in the last case. The piston rods also terminate in connecting rods working on to the crank shaft. The air cylinders are each 88 in. in diameter, and the high and low pressure cylinders of the compound steam engine are 30 in. and 64 in. respectively, while the common stroke of all four is 60 in. The pressure of the air delivered varies from 4½ to 10 ℔ per sq. in. and the quantity per minute is 25,000 cub. ft. Each engine develops about 1200 horse-power. It is to be noted that flap valves such as those used in the 1851 Dowlais engine have in most cases given place to a larger number of circular steel disk valves, held to their seats by springs.
In a large blowing engine built in 1905 by Messrs Davy Bros. of Sheffield for the North-Eastern Steel Company at Middlesbrough (seeEngineering, January 6, 1905) the same arrangement was adopted as in that just described. The two air cylinders are each 90 in. diameter and have a stroke of 72 in. The capacity of this engine is 52,000 cub. ft. of air per minute, delivered at a pressure of from 12½ to 15 ℔ per sq. in. when running at a speed of thirty-three revolutions per minute. The air valves consist of a large number of steel disks resting on circular seatings and held down by springs, which for the delivery valves are so adjusted in strength that they lift and release the air when the desired working pressure has been reached. It is worthy of note that in this engine no attempt is made to make the air pistons air-tight in the usual way by having packing rings set in grooves round the edge, but the piston is made deeper than usual and turned so as to be a very good fit in the cylinder and one or two small grooves are cut round the edge to hold the lubricant.
To illustrate a blowing engine driven by a gas engine supplied with blast furnace gas, fig. 5 gives a diagrammatic view of the blowing cylinder of an engine built by Messrs Richardsons, Westgarth & Co. of Middlesbrough about 1905. The gas cylinder is not shown. It will be seen that the air cylinder is horizontal, and it is arranged to work in tandem with the gas motor cylinder. The chief point of interest is to be found in the arrangement of the details of the air cylinder. Its diameter is 86½ in. and the length of piston stroke 55 in. As to the arrangement of the valves, if the piston be moving in the direction shown, on the left side of the piston at A air is being discharged, and follows the course indicated by the arrows, so as first to pass into the annular chamber which forms a continuation of thespace A, and thence, through the spring-controlled steel disk valves v′, into the discharge chamber C, which ultimately leads to the blast pipe. It will be seen that the valves v on the other side of the annular chamber are closed. At the same time a partial vacuum is being formed in the space B, to be filled by the inflow of air through the valves v which are now open, the corresponding discharge valves v′ being closed. These valves on the inside and outside of the annular spaces referred to are arranged so as to form a circle round the ends of the barrel of the cylinder. The free air, instead of being drawn into the valves v direct from the air of the engine house, is taken from an enclosed annular chamber E, which may be in communication with the clean, cool air outside. It will be seen that the piston is made deep so as to allow for a long bearing surface in the cylinder. Two metal packing rings are provided to render the piston air-tight. The horse-power of this engine, which is designed on the Cockerell system, is 750.
Air valves of other types than those which have been mentioned have been tried, such as sliding grid valves, rotatory slide valves and piston valves, but it has been found that either flap or disk lift valves are more satisfactory for air on account of the grit which is liable to get between slide valves and their seatings. In some of the blowing engines made by Messrs Fraser & Chalmers (seeEngineer, June 15, 1906), sheets of flexible bronze act as flap valves both for admission and delivery, the part which actually closes the opening being thickened for strength.
The pressure of the air supplied by blowing engines depends upon the purposes for which it is to be used. In charcoal furnaces the pressure is very low, being less than 1 ℔ per sq. in.; for blast furnaces using coal an average value of 4 ℔ is common; for American blast furnaces using coke or anthracite coal the pressure is as high as 10 ℔; while for the air required in the Bessemer process of steel-making pressures up to 25 or 30 ℔ per sq. in. are not uncommon. According to British practice one large blowing engine is used to supply several blast furnaces, while in America a number of smaller ones is used, one for each furnace.
Rotary blowersoccupy a position midway between blowing engines and fan blowers, being used for purposes requiring the delivery of large volumes of air at pressures lower than those of blowing engines, but higher than those of fan blowers. The blowing engine draws in, compresses and delivers its air by the direct action of air-tight pistons; the same effect is aimed at in a rotary blower with the difference that the piston revolves instead of moving up and down a cylinder.
Two of the best-known machines of this kind are Roots’ and Baker’s, both American devices. The mode of action of Roots’ blower, as made by Messrs Thwaites Bros. of Bradford, will be clear from the section shown on fig. 6. The moving parts work in a closed casing B, which consists of half-cylindrical curved plates placed a little more than their own radius apart, the ends being enclosed by two plates. Within the casing, and barely touching the curved part of the casing and each other, revolve two parts C, D, called “revolvers,” the speed of rotation of which is the same, but the direction opposite. They are compelled to keep their proper relative positions by a pair of equal spur wheels fixed on the ends of the shafts on which they run. The free air enters the casing through a wire screen at A and passes into the space E.
As the space E increases in volume owing to the movement of the revolvers, air is drawn in; it is then imprisoned between D and the casing, as shown at G, and is carried round until it is free to enter F, from which it is in turn expelled by the lessening of this space as the lower ends of the revolvers come together. In this way a series of volumes of air is drawn in through A, to be afterwards expelled from H in an almost perfectly continuous stream, this result being brought about by the relative variation in volume of the spaces E, F and G. In their most improved form the revolvers are made hollow, of cast iron, and accurately machined to a form such that they always keep close to one another and to the end casing without actually touching, there being never more space for the escape of air than1⁄32nd of an inch. Machines after this design are made from the smallest size, delivering 25 cub. ft., to the largest, with a capacity of 25,000 cub. ft. per minute working up to a pressure of 3 ℔ per sq. in. It is not found economical to attempt to work at higher pressures, as the leakage between the revolvers and the casing becomes too great; where a higher pressure is desired two or more blowers can be worked in series, the air being raised in pressure by steps. A blower using 1 H.P. will deliver 350 cub. ft. of air per minute and one using 2¾ H.P. will deliver 800 cub. ft., at a pressure suitable for smiths’ fires. At the higher pressure required for cupola work—somewhere about ¾ ℔ per sq. in.—6½ H.P. will deliver 1300, and 123 H.P. 25,000 cub. ft. per minute. In the Baker blower three revolvers are used—a large one which acts as the rotating piston and two smaller ones forming air locks or valves.
Rotary Fans.—Now that power for driving them is so generally available, rotary blowing fans have for many purposes taken the place of bellows. They are used for blowing smiths’ fires, for supplying the blast for iron melting cupolas and furnaces and the forced draught for boiler fires, and for any other purpose requiring a strong blast of air. Their construction will be clear from the two views (figs. 7 and 8) of the form made by Messrs Günther of Oldham, Lancashire. The fan consists of a circular casing A having the general appearance of a snail shell. Within this casing revolves a series of vanes B—in this case five—curved as shown, and attached together so as to form a wheel whose centre is a boss or hub. This boss is fixed to a shaft or spindle which revolves in bearings supported on brackets outside the casing. As the shaft is rotated, the vanes B are compelled to revolve in the direction indicated by the arrow on fig. 7, and their rotation causes the air within the casing to rotate also. Thus a centrifugal action is set up by which there is a diminution of pressure at the centre of the fan and an increase against the outer casing. In consequence air is sucked in, as shown by the arrows on fig. 8, through the openings C, C, at the centre of the casing around the spindle. At the same time the air which has been forced towards the outside of the casing and given a rotary motion is expelled from the opening at D (fig. 8). All blowing fans work on the same principle, though differences in detail are adopted by different makers to meet the variety of conditions under which they are to be used. Where the fan is to be employed for producing a delivery or blast of air the opening D is connected to an air pipe which serves to transmit the current of air, and C is left open to the atmosphere; when, however, the main object is suction, as in the case where the fan is used for ventilation, the aperture C is connected through a suction pipe with the space to be exhausted, D being usually left open. Günther fans range in size from those which have a diameter of fan disk of 8 in. and make 5500 revolutions per minute, to those which have a diameter of 50 in. and run at from 950 to 1200 revolutions per minute. For exhausting the fans are run less quickly than for blowing, the speed for a fan of 10 in. diameter being 4800 revolutions for blowing and 3300-4000 for exhausting, while the 50-in. fan only runs at 550-700 when exhausting. These two exhausting fans remove 400-500 and 12,000-15,000 cub. ft. of air per minute respectively.
The useful effect of rotary fans, that is to say the proportion of the total power used to drive the fan which is actually utilized in producing the current of air, is very low for the smaller sizes, but may rise to 30-70% in sizes above 5 ft. in diameter. It has its maximum value for any given fan at a certain definite speed. Fans are most suitable in cases where it is required to move or deliver comparatively large volumes of air at pressures which are little above that of the atmosphere. Where the pressure of the current produced exceeds a quarter of a pound on the square inch the waste of work becomes so great as to preclude their use. The fan is not the most economical form of blower, but it is simple and inexpensive, both in first cost and in maintenance. The largest fans are used for ventilating purposes, chiefly in mines, their diameters rising to 40 or even 50 ft. The useful effect of some of these larger fans, as obtained from experiments, is as high as 75%. In the case of the Capell fan, which differs from other forms in that it has two series of blades, inner and outer, separated by a curved blank piece between the inner wings, dipping into the fan inlet, and the outer wings, very high efficiencies have been obtained, being as great as 90% in some cases. Capell fans are used for ventilating mines, buildings, and ships, and for providing induced currents for use in boiler furnaces. In the larger fans the casing, instead of having a curved section, is more often built of sheet steel and is given a rectangular section at right angles to the periphery. The Sirocco blowing fan, of Messrs Davidson of Belfast, has a larger number of blades, which are relatively narrow as measured radially, but wide axially. It can be made much smaller in diameter than fans of the older designs for the same output of air—a great advantage for use in ships or in buildings where space is limited—and its useful effect is also said to be superior. (See alsoHydraulics, § 213.)
Helical or screw blowers, often called “air propellers,” are used where relatively large volumes of air have to be moved against hardly any perceptible difference in pressure, chiefly for purposes of ventilation and drying. Most often the propeller is used to move air from one room or chamber to another adjoining, and is placed in a light circular iron frame which is fixed in a hole in the wall through which the air is to be passed. The propeller itself consists of a series of vanes or wings arranged helically on a revolving shaft which is fixed in the centre of the opening. The centre line of the shaft is perpendicular to the plane of the opening so that when the vanes revolve the air is drawn towards and through the opening and is propelled away from it as it passes through. The action is similar to that of a steamship screw propeller, air taking the place of water. Such blowers are often driven by small electric motors working directly on the end of the shaft. For moving large volumes of air against little pressure and suction they are very suitable, being simpler than fans, cheaper both in first cost and maintenance for the same volume of air delivered, and less likely to fail or get out of order. To obtain the best effect for the power used a certain maximum speed of rotation must not be exceeded; at higher speeds a great deal of the power is wasted. For example, a propeller with a vane diameter of 2½ ft. was found to deliver a volume of air approximately proportional to the speed up to about 700 revolutions per minute, when 8000 cub. ft. per minute were passed through the machine; but doubling this speed to 1400 revolutions per minute only increased delivery by 1000 cub. ft. to 9000. At the lower of these speeds the horse-power absorbed was 0.6 and at the higher one 1.6.
Other Appliances for producing Currents of Air.—In its primitive form the “trompe” or water-blowing engine adopted in Savoy, Carniola, and some parts of America, consists of a long vertical wooden pipe terminating at its lower end in an air chest. Water is allowed to enter the top of the pipe through a conical plug and, falling down in streamlets, carries with it air which is drawn in through sloping holes near the top of the pipe. In this way a quantity of air is delivered into the chamber, its pressure depending on the height through which the water falls. This simple arrangement has been developed for use in compressing large volumes of air at high pressures to be used for driving compressed air machinery. It is chiefly used in America, and provides a simple and cheap means of obtaining compressed air where there is an abundant natural supply of water falling through a considerable height. The pressure obtained in the air vessel is somewhat less than half a pound per square inch for every foot of fall.
Natural sources of water are also used for compressing and discharging air by letting the water under its natural pressure enter and leave closed vessels, so alternately discharging and drawing in new supplies of air. Here the action is the same as in a blowing engine, the water taking the place of the piston. This method was first thoroughly developed in connexion with the Mt. Cenis tunnel works, and its use has since been extended.
In thejet blower(fig. 9) a jet of steam is used to induce a current of air. Into one end of a trumpet-shaped pipe B projects a steam pipe A. This steam pipe terminates in a small opening, say, one-eighth of an inch, through which the steam is allowed toflow freely. The effect is to cause a movement of the air in the pipe, with the result that a fresh supply is drawn in through the annular opening at C, C, and a continuous stream of air passes along the pipe. This is the form of blower made by Messrs Meldrum Bros. of Manchester, and is largely used for delivering air under the fire bars of boiler and other furnaces. In some cases the jets of steam are allowed to enter a boiler furnace above the fire, thus inducing a current of air which helps the chimney draught and is often used to do away with the production of smoke; they are also used for producing currents of air for purposes other than those of boiler fires, and are very convenient where considerable quantities of air are wanted at very low pressures and where the presence of the moisture of the steam does not matter.
Sometimes jets of high-pressure air flowing at great velocities are used to induce more slowly-moving currents of larger volumes of air at low pressures.
(W. C. P.)
1The Old English word for this appliance wasblástbaelig,i.e.“blow-bag,” cf. GermanBlasebalg. By the 11th century the first part of the word apparently dropped out of use, andbaelig, bylig, bag, is found in early glossaries as the equivalent of the Latinfollis. Baeligbecame in Middle Englishbely,i.e.“belly,” a sack or bag, and so the general word for the lower part of the trunk in man and animals, the stomach, and another form, probably northern in origin,belu, belw, became the regular word for the appliance, the plural “bellies” being still used till the 16th century, when “bellows” appears, and the word in the singular ceases to be used. The verb “to bellow” of the roar of a bull, or the low of a cow, is from Old Englishbellan, to bell, roar.
1The Old English word for this appliance wasblástbaelig,i.e.“blow-bag,” cf. GermanBlasebalg. By the 11th century the first part of the word apparently dropped out of use, andbaelig, bylig, bag, is found in early glossaries as the equivalent of the Latinfollis. Baeligbecame in Middle Englishbely,i.e.“belly,” a sack or bag, and so the general word for the lower part of the trunk in man and animals, the stomach, and another form, probably northern in origin,belu, belw, became the regular word for the appliance, the plural “bellies” being still used till the 16th century, when “bellows” appears, and the word in the singular ceases to be used. The verb “to bellow” of the roar of a bull, or the low of a cow, is from Old Englishbellan, to bell, roar.
BELLOY, DORMONT DE,the name assumed byPierre Laurext Buireite(1727-1775), French dramatist, was born at Saint-Flour, in Auvergne, on the 17th of November 1727. He was educated by his uncle, a distinguished advocate in Paris, for the bar. To escape from a profession he disliked he joined a troupe of comedians playing in the courts of the northern sovereigns. In 1758 the performance of hisTitus, which had already been produced in St Petersburg, was postponed through his uncle’s exertions; and when it did appear, a hostile cabal procured its failure, and it was not until after his guardian’s death that de Belloy returned to Paris withZelmire(1762), a fantastic drama which met with great success. This was followed in 1765 by the patriotic play,Le Siège de Calais. The moment was opportune. The humiliations undergone by France in the Seven Years’ War assured a good reception for a play in which the devotion of Frenchmen redeemed disaster. The popular enthusiasm was unaffected by the judgment of calmer critics such as Diderot and Voltaire, who pointed out that the glorification of France was not best effected by a picture of defeat. De Belloy was admitted to the Academy in 1772. His attempt to introduce national subjects into French drama deserves honour, but it must be confessed that his resources proved unequal to the task. TheSiège de Calaiswas followed byGaston et Bayard(1771),Pedro le cruel(1772) andGabrielle de Vergy(1777). None of these attained the success of the earlier play, and de Belloy’s death, which took place on the 5th of March 1775, is said to have been hastened by disappointment.
BELLorINCHCAPE ROCK,a sandstone reef in the North Sea, 11 m. S.E. of Arbroath, belonging to Forfarshire, Scotland. It measures 2000 ft. in length, is under water at high tide, but at low tide is exposed for a few feet, the sea for a distance of 100 yds. around being then only three fathoms deep. Lying in the fairway of vessels making or leaving the Tay and Forth, besides ports farther north, it was a constant menace to navigation. In the great gale of 1799 seventy sail, including the “York,” 74 guns, were wrecked off the reef, and this disaster compelled the authorities to take steps to protect shipping. Next year Robert Stevenson modelled a tower and reported that its erection was feasible, but it was only in 1806 that parliamentary powers were obtained, and operations began in August 1807. Though John Rennie had meanwhile been associated with Stevenson as consulting engineer, the structure in design and details is wholly Stevenson’s work. The tower is 100 ft. high; its diameter at the base is 42 ft., decreasing to 15 ft. at the top. It is solid for 30 ft. at which height the doorway is placed. The interior is divided into six storeys. After five years the building was finished at a cost of £61,300. Since the lighting no wrecks have occurred on the reef. A bust of Stevenson by Samuel Joseph (d. 1850) was placed in the tower.
According to tradition an abbot of Aberbrothock (Arbroath) had ordered a bell—whence the name of the rock—to be fastened to the reef in such a way that it should respond to the movements of the waves, and thus always ring out a warning to mariners. This signal was wantonly destroyed by a pirate, whose ship was afterwards wrecked at this very spot, the rover and his men being drowned. Southey made the incident the subject of his ballad of “The Inchcape Rock.”
BELLUNO(anc.Bellunum), a city and episcopal see of Venetia, Italy, the capital of the province of Belluno, N. of Treviso, 54 m. by rail and 28 m. direct. Pop. (1901) town, 6898; commune, 19,050. It is situated in the valley of the Piave, at its confluence with the Ardo, 1285 ft. above sea-level, among the lower Venetian Alps. It was a Romanmunicipium. In the middle ages it went through various vicissitudes; it fell under the dominion of Venice in 1511, and remained Venetian until 1797. Its buildings present Venetian characteristics; it has some good palaces, notably the fine early Lombard Renaissance Palazzo dei Rettori, now the seat of the prefecture. The cathedral, erected after 1517 by Tullio Lombardo, was much damaged by the earthquake of 1873, which destroyed a considerable portion of the town, though the campanile, 217 ft. high, erected in 1732-1743, stood firm. The façade was never finished. Important remains of prehistoric settlements have been found in the vicinity; cf. G. Ghirardini inNotizie degli Scavi, 1883, 27, on the necropolis of Caverzano.
(T. As.)
BELMONT, AUGUST(1816-1890), American banker and financier, was born at Alzei, Rhenish Prussia, on the 8th of December 1816. He entered the banking house of the Rothschilds at Frankfort at the age of fourteen, acted as their agent for a time at Naples, and in 1837 settled in New York as their American representative. He became an American citizen, and married a daughter of Commodore Matthew C. Perry. He was the consul-general of Austria at New York from 1844 to 1850, when he resigned in protest against Austria’s treatment of Hungary. In 1853-1855 he was chargé d’affaires for the United States at the Hague, and from 1855 to 1858 was the American minister resident there. In 1860 he was a delegate to the Democratic National Convention at Charleston, South Carolina, actively supporting Stephen A. Douglas for the presidential nomination, and afterwards joining those who withdrew to the convention at Baltimore, Maryland, where he was chosen chairman of the National Democratic Committee. He energetically supported the Union cause during the Civil War, and exerted a strong influence in favour of the North upon the merchants and financiers of England and France. He remained at the head of the Democratic organization until 1872. He died in New York on the 24th of November 1890.
His son,Perry Belmont(1851- ), was born in New York on the 28th of December 1851, graduated at Harvard in 1872 and at the Columbia Law School in 1876, and practised law in New York for five years. He was a Democratic member of Congress from 1881 to 1889, serving in 1885-1887 as chairman of the committee on foreign affairs. In 1889 he was United States minister to Spain.
Another son,August Belmont(1853- ), was born in New York on the 18th of February 1853 and graduated at Harvard in 1875. He succeeded his father as head of the banking house and was prominent in railway finance, and in financing and building the New York subway. In 1904 he was one of the principal supporters of Alton B. Parker for the Democratic presidential nomination, and served as chairman of the finance committee of the Democratic National Committee.
A volume entitledLetters, Speeches and Addresses of August Belmont(the elder) was published at New York in 1890.
A volume entitledLetters, Speeches and Addresses of August Belmont(the elder) was published at New York in 1890.
BELOIT,a city of Rock county, Wisconsin, U.S.A., situated on the S. boundary of the state, on Rock river, about 91 m. N.W. of Chicago and about 85 m. S.W. of Milwaukee. Pop. (1890) 6315; (1900) 10,436, of whom 1468 were foreign-born; (1910) 15,125. It is served by the Chicago & North-Western, and the Chicago, Milwaukee & St Paul railways, and by an inter-urban electric railway to Janesville, Wisconsin and Rockford, Illinois. Beloit is attractively situated on high bluffs on both sides of the river. The city is the seat of Beloit College, a co-educational, non-sectarian institution, founded under the auspices of the Congregational and Presbyterian churches in 1847, and having, in 1907-1908, 36 instructors and 430 students. It has classical, philosophical (1874) and scientific (1892) courses;women were first admitted in 1895. The Greek department of the college has supervised since 1895 the public presentation nearly every year of an English version of a Greek play. The river furnishes good water-power, and among the manufactures are wood-working machinery, ploughs, steam pumps, windmills, gas engines, paper-mill machinery, cutlery, flour, ladies’ shoes, cyclometers and paper; the total value of the factory product in 1905 was $4,485,224, 60.2% more than in 1900. Beloit, founded by New Englanders in 1838, was chartered as a city in 1856.
BELOMANCY(fromβέλος, a dart, andμαντεία, prophecy or divination), a form of divination (q.v.) by means of arrows, practised by the Babylonians, Scythians and other ancient peoples. Nebuchadrezzar (Ezek. xxi. 21) resorted to this practice “when he stood in the parting of the way ... to use divination: he made his arrows bright.”
BELON, PIERRE(1517-1564), French naturalist, was born about 1517 near Le Mans (Sarthe). He studied medicine at Paris, where he took the degree of doctor, and then became a pupil of the botanist Valerius Cordus (1515-1544) at Wittenberg, with whom he travelled in Germany. On his return to France he was taken under the patronage of Cardinal de Tournon, who furnished him with means for undertaking an extensive scientific journey. Starting in 1546, he travelled through Greece, Asia Minor, Egypt, Arabia and Palestine, and returned in 1549. A full account of his travels, with illustrations, was published in 1553. Belon, who was highly favoured both by Henry II. and by Charles IX., was assassinated at Paris one evening in April 1564, when coming through the Bois de Boulogne. Besides the narrative of his travels he wrote several scientific works of considerable value, particularly theHistoire naturelle des estranges poissons(1551),De aquatilibus(1553), andL’Histoire de la nature des oyseaux(1555), which entitle him to be regarded as one of the first workers in the science of comparative anatomy.
BELPER,a market-town in the mid-parliamentary division of Derbyshire, England, on the river Derwent, 7 m. N. of Derby on the Midland railway. Pop. of urban district (1901), 10,934. The chapel of St John is said to have been founded by Edmund Crouchback, second son of Henry III., about the middle of the 13th century. There is an Anglican convent of the Sisters of St Lawrence, with orphanage and school. For a considerable period one of the most flourishing towns in the county, Belper owed its prosperity to the establishment of cotton works in 1776 by Messrs Strutt, the title of Baron Belper (cr. 1856), in the Strutt family, being taken from the town. Belper also manufactures linen, hosiery, silk and earthenware; and after the decline of nail-making, once an important industry, engineering works and iron foundries were opened. The Derwent provides water-power for the cotton-mills. John of Gaunt is said to have been a great benefactor to Belper, and the foundations of a massive building have been believed to mark the site of his residence. A chapel which he founded is incorporated with a modern schoolhouse. The scenery in the neighbourhood of Belper, especially to the west, is beautiful; but there are collieries, lead-mines and quarries in the vicinity of the town.
Belper (Beaurepaire) until 1846 formed part of the parish of Duffield, granted by William I. to Henry de Ferrers, earl of Derby. There is no distinct mention of Belper till 1296, when the manor was held by Edmund Crouchback, earl of Lancaster, who is said to have enclosed a park and built a hunting seat, to which, from its situation, he gave the name Beaurepaire. The manor thus became parcel of the duchy of Lancaster and is said to have been the residence of John of Gaunt. It afterwards passed with Duffield to the Jodrell family. In a great storm in 1545, 40 houses were destroyed, and the place was scourged by the plague in 1609.
See C. Willott,Historical Records of Belper.
See C. Willott,Historical Records of Belper.
BELSHAM, THOMAS(1750-1829), English Unitarian minister, was born at Bedford on the 26th of April 1750. He was educated at the dissenting academy at Daventry, where for seven years he acted as assistant tutor. After three years spent in a charge at Worcester, he returned as head of the Daventry academy, a post which he continued to hold till 1789, when, having adopted Unitarian principles, he resigned. With Joseph Priestly for colleague, he superintended during its brief existence a new college at Hackney, and was, on Priestly’s departure in 1794, also called to the charge of the Gravel Pit congregation. In 1805 he accepted a call to the Essex Street chapel, where in gradually failing health he remained till his death in 1829. Belsham’s first work of importance,Review of Mr Wilberforce’s Treatise entitled Practical View(1798), was written after his conversion to Unitarianism. His most popular work was theEvidences of Christianity;the most important was his translation and exposition of the Epistles of St Paul (1822). He was also the author of a work on philosophy,Elements of the Philosophy of the Human Mind(1801), which is entirely based on Hartley’s psychology. Belsham is one of the most vigorous and able writers of his church, and theQuarterly ReviewandGentleman’s Magazineof the early years of the 19th century abound in evidences that his abilities were recognized by his opponents.
BELSHAZZAR(6th centuryB.C.), Babylonian general. Until the decipherment of the cuneiform inscriptions, he was known only from the book of Daniel (v. 2, 11, 13, 18) and its reproduction in Josephus, where he is represented as the son of Nebuchadrezzar and the last king of Babylon. As his name did not appear in the list of the successors of Nebuchadrezzar handed down by the Greek writers, various suggestions were put forward as to his identity. Niebuhr identified him with Evil-Merodach, Ewald with Nabonidos, others again with Neriglissor. The identification with Nabonidos, the last Babylonian king according to the native historian Berossus, goes back to Josephus. The decipherment of the cuneiform texts put an end to all such speculations. In 1854 Sir H.C. Rawlinson discovered the name of Bel-sarra-uzur—“O Bel, defend the king”—in an inscription belonging to the first year of Nabonidos which had been discovered in the ruins of the temple of the Moon-god at Muqayyar or Ur. Here Nabonidos calls him his “first-born son,” and prays that “he may not give way to sin,” but that “the fear of the great divinity” of the Moon-god may “dwell in his heart.” In the contracts and similar documents there are frequent references to Belshazzar, who is sometimes entitled simply “the son of the king.”
He was never king himself, nor was he son of Nebuchadrezzar. Indeed his father Nabonidos (Nabunaid), the son of Nabu-baladsu-iqbi, was not related to the family of Nebuchadrezzar and owed his accession to the throne to a palace revolution. Belshazzar, however, seems to have had more political and military energy than his father, whose tastes were antiquarian and religious; he took command of the army, living with it in the camp near Sippara, and whatever measures of defence were organized against the invasion of Cyrus appear to have been due to him. Hence Jewish tradition substituted him for his less-known father, and rightly concluded that his death marked the fall of the Babylonian monarchy. We learn from the Babylonian Chronicle that from the 7th year of Nabonidos (548B.C.) onwards “the son of the king” was with the army in Akkad, that is in the close neighbourhood of Sippara. This, as Dr Th. G. Pinches has pointed out, doubtless accounts for the numerous gifts bestowed by him on the temple of the Sun-god at Sippara. So late as the 5th of Ab in the 17th year of Nabonidos—that is to say, about three weeks after the forces of Cyrus had entered Babylonia and only three months before his death—we find him paying 47 shekels of silver to the temple on behalf of his sister, this being the amount of “tithe” due from her at the time. At an earlier period there is frequent mention of his trading transactions which were carried out through his house-steward or agent. Thus in 545B.C.he lent 20 manehs of silver to a private individual, a Persian by race, on the security of the property of the latter, and a year later his house-steward negotiated a loan of 16 shekels, taking as security the produce of a field of corn.
The legends of Belshazzar’s feast and of the siege and capture of Babylon by Cyrus which have come down to us from the book of Daniel and theCyropaediaof Xenophon have been shown by the contemporaneous inscriptions to have been a projectionbackwards of the re-conquest of the city by Darius Hystaspis. The actual facts were very different. Cyrus had invaded Babylonia from two directions, he himself marching towards the confluence of the Tigris and Diyaleh, while Gobryas, the satrap of Kurdistan, led another body of troops along the course of the Adhem. The portion of the Babylonian army to which the protection of the eastern frontier had been entrusted was defeated at Opis on the banks of the Nizallat, and the invaders poured across the Tigris into Babylonia. On the 14th of Tammuz (June), 538B.C., Nabonidos fled from Sippara, where he had taken his son’s place in the camp, and the city surrendered at once to the enemy. Meanwhile Gobryas had been despatched to Babylon, which opened its gates to the invader on the 16th of the month “without combat or battle,” and a few days later Nabonidos was dragged from his hiding-place and made a prisoner. According to Berossus he was subsequently appointed governor of Karmania by his conqueror. Belshazzar, however, still held out, and it was probably on this account that Cyrus himself did not arrive at Babylon until nearly four months later, on the 3rd of Marchesvan. On the 11th of that month Gobryas was despatched to put an end to the last semblance of resistance in the country “and the son (?) of the king died.” In accordance with the conciliatory policy of Cyrus, a general mourning was proclaimed on account of his death, and this lasted for six days, from the 27th of Adar to the 3rd of Nisan. Unfortunately the character representing the word “son” is indistinct on the tablet which contains the annals of Nabonidos, so that the reading is not absolutely certain. The only other reading possible, however, is “and the king died,” and this reading is excluded partly by the fact that Nabonidos afterwards became a Persian satrap, partly by the silence which would otherwise be maintained by the “Annals” in regard to the fate of Belshazzar. Considering how important Belshazzar was politically, and what a prominent place he occupied in the history of the period, such a silence would be hard to explain. His death subsequently to the surrender of Babylon and the capture of Nabonidos, and with it the last native effort to resist the invader, would account for the position he assumed in later tradition and the substitution of his name for that of the actual king.