Fig. 158.J.N.
Fig. 158.J.N.
(304) The controlling mechanism is shown in Fig.159, which is a representation of the parts affecting the counter faller. Hinged, as shown, to a bracket on the underside of the carriage is a leverJ, to which are attached two chainsE1I. The former is coupled to a sectorE, which is secured on the counter faller shaft or rodB1. If it is assumed that the latter is free to rotate, as it is, the pull exercised by the leverJwould be sufficient to cause it to do so. But until the winding faller makes its descent so as to assume the winding position, as afterwards described, the weight of the leverJis taken by the chainI, which at its upper end is fixed to the hook shown. The latter is hinged to the bracket or leverS, the other arm. of which rests upon the counter faller rodB1, and thus limits the upward movement of the winding faller.A steady torsional pull is exercised upon the bracketS, so as to draw the chainIupwards, by the springV, attached as shown. The unwinding of the two or three coils of yarn during backing-off takes place during the time the winding faller is descending. Immediately backing-off is completed, the carriage begins to run in, and the yarn is wound. It is therefore necessary for the counter faller to rise, so as to take up any slack yarn. Unless this is done, the yarn—owing to its tightly twisted condition—runs into small loops or kinks, technically known as “snarls.” The oscillation of the winding faller rodBhas caused a similar movement inS, and, as a result, the chainIbecomes slackened and ceases to sustain the leverJ. As, therefore, the carriageObegins to run in the leverJdescends, and the whole of its weight is borne by the chainE1, which is caused to pull upon the sectorE. In this way the counter faller rodB1is oscillated, and the counter faller wireMis raised. The extent of its upward movement is regulated solely by the tension of the threads, which is sufficient to act as a counterbalance to the leverJ. In order that this equilibrium shall be sufficient to preserve the necessary tightness of the threads, without any danger existing of either slack threads or of the counter faller being unyielding when an extra strain is put upon the yarn, balance weights can be added at the end of the leverJ, as shown. In this way the necessary sustainment of the yarn threads is obtained without any likelihood of straining or breakage. When the carriage has completed its inward run the weight of the leverJis relieved by the rollerW, so that the faller, when released, as afterwards described, can easily assume its proper position during spinning or twisting.
(305) While the counter faller is being freed in the manner described the downward movement of the faller is also proceeding. Referring now to Fig.160, which is a detailed view of the faller arrangement, the faller shaft has fixed on it an arm or backing-off fingerD, to which is fastened one end of a chainE. One end ofEpasses round the small bowlF, and its other end is fastened to a snail or scrollGmounted on the tin roller shaft. The snail is geared by a ratchet clutch which engages only when the tin roller is revolving during backing-off, being disengaged during the whole period of spinning. The size of the snail is arranged so as to draw down the faller fingerDduring the period of backing off to such an extent that the faller is brought into the proper position for the commencement of winding. In dealing with the latter operation it will be shown that the faller is a little below the cop nose when winding begins, and then rapidly descends until the base of the upper cone is reached. At present it is only necessary to note this fact, as it has a somewhat important bearing on the mechanism being described. During the period of the faller descent a pull is exercised on the rodF1, by which the bowl or runnerFis carried. The other end ofFis hinged to the “locking” leverA, to which the curved arm or sectorCis hinged at its upper end. This arm is fixed on the faller shaft, so that the oscillation of the latter, which is caused by the pull of the chainE, gradually raises the “locking” leverA. This elevation goes on until the shoulder or bracketKis high enough for its under side to slip over the small bowl fixed in the lever or slideL. The latter is at the end of a lever hinged at one end to the carriage and carrying the runner or bowlL1. This is drawn along with the carriage, and the lever is consequently called the “trail” lever. As soon asKslips on to the bowl inLthe “locking” lever and faller are said to be “locked,” and are then in a position to begin winding.This action is practically simultaneous with the termination of backing-off. This method of locking the faller is now general, having quite superseded the older method of locking at the top.
Fig. 160.J.N.
Fig. 160.J.N.
(306) In order to render the action of backing-off more perfect, and to ensure that the slack of the yarn, as it is unwound, shall be taken up by the faller, Messrs. Platt Brothers and Company have adopted the mechanism also shown in Fig.160. The reversal of the direction of rotation of the spindles takes place a little in advance of the downward movement of the faller, and it is therefore found that a short length of yarn is unwound before the faller presses upon it. The actual extent of the unwinding is relatively greatest when the cop is almost built. It therefore becomes necessary to expedite the action of the backing-off chain as the cops are built, so that the faller is drawn into contact with the yarn at the earliest moment. A little reflection will show that at the period when the cops are beginning to be built the faller wire has a much longer distance to travel than when they are almost finished. As will be afterwards shown, the period at which the faller is locked is gradually made earlier as building proceeds, so that a much shorter traverse of the faller prior to locking takes place correspondingly. Thus, for instance, if it has to be depressed one inch before it touches the yarn at the commencement of a set of cops, the relative proportion of that distance to the whole traverse prior to locking is less than when the traverse is so much diminished at the end of a set. Thus it follows that a degree of lagging permissible at one stage is absolutely detrimental at the other. From this it may bededuced that an earlier and accelerated motion of the faller is necessary in order to take up the slack yarn during backing off.
Fig. 159.J.N.
Fig. 159.J.N.
(307) It is hardly practicable to fit a motion of absolute accuracy to effect this purpose, but an approximation to it can be obtained. It is, therefore, arranged that at the beginning of a set the backing-off chain shall be slack, and during building shall be gradually tightened until at the end of it is nearly in a state of tension. The snail is proportioned so as to give a quick downward movement to the faller, and in combination with the arrangement about to be described gives very good results. Referring again to Fig.160, attached to the snailGis a second chain, the other end of which is fastened to a leverH, hinged on the bracket shown. The other end ofHrests on an inclined plateN, which slides on a bedplate fastened to the floor. The plateNis fastened to the copping plate connecting rod—afterwards referred to—which passes through a horn fastened onN. As the copping plate is moved in,His also caused to assume the position indicated by the dotted lines,Nhaving also moved in. The effect is that a pull is put upon the snail which gradually rotates it, and causes it to wind onthe slack of the chainE, so that, when backing-off occurs, the faller is drawn downwards at an earlier moment. The restoration ofNto its original position accompanies that of the copping plate, and is made at the beginning of a new set of cops.
(308) The various movements in connection with backing-off having thus been described, it is necessary to show how the traverse of the faller is obtained during the inward traverse of the carriage. This is shown in Fig.161, page 205, which is a separate view of the copping or building mechanism. The faller “locking” leverAis, as has been described, raised until the shoulderRslips on to the slideL, in which position it remains until it is released at the termination of the inward run. On the underside ofLa small bowl or runnerL1is carried, which rests upon the upper surface of a longitudinal, or “copping” railP, made of a strong section. If the latter was placed in such a position that its upper surface was horizontal, it is plain that the slideLwould receive no vertical motion during the period that the runnerL1was traversing it. In consequence the sickleUwould remain in one position during the same time. But if the railPis raised at one end so that its upper edge is inclined, the slideLwill, during the run in of the carriage, receive a vertical traverse corresponding to the difference in the altitude of the two ends of the copping rail. That is to say, if one end of the rail was six inches from the floor line, while the other end was seven,Lwould ascend or descend to the extent of one inch while it was travelling from one end to the other of the railP. The question as to whether it would ascend or descend depends entirely upon which end of the rail was highest. From this it may be inferred that by varying the angularity or profile of the copping rail any desired traverse, either regular or intermittent, could be given to the slideL. Now it was shown that the winding faller sickles are keyed on the shaftB, which is oscillated by the backing-off fingerDfastened upon it. The latter being jointed to the “locking” leverA, it follows, that, as the latter is raised, the winding faller moves in an arc, which corresponds in length and direction to the length and inclination of the copping rail.
(309) It is necessary when the carriage arrives at the end of its stretch to lock it in that position during the time that backing-off is taking place, and the motions of releasing the counter faller and locking the winding faller are in operation. A reference to Fig.162is necessary to understand this part of the mechanism. That illustration is a diagrammatic representation of the mechanism relating to locking the carriage, and the engagement and disengagement of the taking-in gear. The parts are not in their working position, but are projected so that their operation may be better understood. The actual relative position of the various motions is shown by the diagrammatic sketch in the right hand top corner of Fig.162. Upon the carriageOa bracketO1is fixed, which carries at its outer end a pin or catch, with which the hook at the end of the horizontal arm of theLleverScan engage. The hook readily falls over the pin inO1, as the carriage is pushed up to it near the end of its traverse. The leverSis coupled in the manner shown to the horizontal rodR, which, at its other end, is jointed to a bell crank leverU1. The rodR, on account of its function, is termed the “holding-out catch rod.” The leverU1is in turn connected with the rodU, jointed at its upper end to the leverW, which is coupled to the horizontal arm of the leverZ1by the connecting rodM. A connection is thus established between the camZon the cam shaft and the “holding-out” catch leverS. During the run out ofthe carriage the friction clutchI1Kis disengaged by means of the leverW. The rodRis also locked by the small vertical slideS1, which engages with the catch notch formed in it. The movement of the backing-off rodX, which is hinged to the leverL, causes the projecting arm in the leverYto be pushed under the end of the leverW, thus sustaining the latter and preventing the engagement of the upper halfI1of the taking-in friction with the lower halfK. This action occurs just before the termination of the outward run, being a little in advance of backing-off, but simultaneous with the compression of the backing-off spring onX. Whatever movement ofWmay take place after the arm onYis thus projected into the path of the end of the leverW, the friction cannot fall into gear until the support of the arm is withdrawn. The whole of these parts are thus locked together, and fall into gear simultaneously. It will be noticed that the connection between the leverSand the rodRis such that the latter can make a certain movement forward before the lever falls. Further, the carriage can be arrested during its outward run by the pedal lever fixed to the floor.
(310) The action of the mechanism is as follows: When the carriage arrives at its outermost point the connecting rodRis unlocked, and is free to move. In this way the catch leverScan be easily raised by the bracket on the carriageO, over which it falls, and securely holds it, the slot in the rodRpermitting this movement. In this position it remains during the whole period of backing-off, when in a way which is afterwards described, it is released simultaneously with the taking-in friction with which, as shown, it is connected. The locking of the carriage is the last operation requiring explanation before proceeding to deal with the movements, which, together, make up the fourth stage or period. This is the one in which the nicest problems require solution, and in which the mechanism used is the most ingenious.
(311) The first step in commencing to wind is, of course, to release the carriage and draw it in. Before proceeding to show how this is effected, it will be as well to recapitulate and describe the position of the various parts. The strap is entirely upon the loose pulley; the backing-off friction clutch is in gear; the spindles are revolving in the opposite direction to that normal to them; the winding faller is drawn down and locked in a position a little below the nose of the cop; the counter faller is held just out of contact with the threads, but free to rise as soon as an inward movement of the carriage occurs; the roller and back shaft clutches are disengaged; and the upper half of the taking-in friction is out of gear with the lower, but revolving with the vertical shaft on which it slides.
(312) When the chainE(Fig.160) has sufficiently raised the faller locking leverAto permit it to lock, the swinging leverVis suddenly drawn back. An examination of the drawings, either Fig.160or Fig.161, will show that so long as the face of the locking lever presses against the face of the slide no lateral movement of the former is possible. Further, the connection established between the locking leverAand the leverV, by means of the leverF1, ensures that as soon as the inward movement of the lever takes place when locking occurs, the leverVmust necessarily oscillate on its pivot. This movement of the leverVcauses its lower jaw to exercise a pressure upon the leverLin the contrary direction to that previously noted, and so draws the stopX1in contact with the bottom of the backing-off leverD. This action is aided by the spring on the backing-off rod, which is free to extend, and its whole force can be exerted on the leverD. In this wayDis drawn back, and the backing-off clutch is disengaged.
(313) The same movement draws away the supporting piece on the vertical leverY, and allows the upper half of the taking-in friction to fall into gear with the lower half, this action being aided by the springQ. The slot in the end of the connecting rodMpermits the upward movement of the left hand end of the leverWto be made rapidly and freely. In this way the engagement of the friction clutch is a very quick one. This upward movement of the leverWis communicated, in a manner described, to the holding out catch, which is also raised nearly simultaneously, and the carriage released.
Fig. 162.J.N.
Fig. 162.J.N.
(314) It is, of course, highly essential that all the three releasing motions shall be accurately “timed,” so as not to take place either before or after the proper moment. Accordingly, ample means of adjustment are provided, both on the rodXby the regulation of the stopsX1andX2; on the connecting rodMcoupling the leversZandT; and also on the holding-out rod. In this way it is possible to secure that simultaneous movement of the three parts, which is so essential for effective working. It is obvious that the backing-off friction and holding-out catch must be released before the taking-in friction gears, but the interval between these is so slight that they occur practically simultaneously.
(315) The taking-in friction being in gear, the rotation of the loose pulley is, by the train of wheels shown, communicated to the “scroll” shaft, on which the taking-in scrolls are fixed. These have bandsattached to and wrapped round them when the carriage is at the roller beam. As the carriage runs out, the bands, which are fastened to it, are drawn off the scrolls, the scroll shaft being then free to revolve. The engagement of the taking-in friction reverses this process and winds on the bands, thus drawing up the carriage. It will be observed that the scrolls vary in diameter, being about 9 inches in the largest part, and about 3 inches in the smallest. The reason of this construction is to give a varying traverse to the carriage, so as to start it easily, and bring it up to the back stops gently. The scrolls are designed so that, so long as they are revolving, they exercise a pull upon the carriage which is steady and constant. In this way, over-running is avoided, but to prevent any possibility of it a scrollL1, shown in a detached position in Fig.153, is fixed onLat an angle of 180 degrees to the others, the point of attachment of its rope being diametrically opposite that on the other scrolls. Thus when the bands on the drawing out scrolls are unwound, that on the “check scroll” is wound and vice versa. The purpose of this scroll is, as its name indicates, to check any tendency to over-running, which it effectually does. In all mules above a certain length, it is desirable to provide some means whereby the carriage shall be drawn in evenly throughout its length, and shall not be in danger of twisting or warping. The scroll shaft, it will be noticed, only extends across the headstock, so that the bands can only exercise any pull on the square, and if no other points of attachment were made, the carriage would at its extremities lag behind the centre. A considerable amount of friction would be thus caused, and the spindles at the end of the carriage would not take up the full length of yarn. It was shown that the back shaft is, during winding, disengaged, so that it is only necessary to establish a connection between it and the scroll shaft, to enable the carriage to be drawn in at several points throughout its length, instead of at one only. Accordingly, the scroll shaft is extended, and an extra scroll shown in Fig.154at the right hand side is fitted, from which a band is taken to a drum upon the back shaft. Thus the back shaft is converted into a taking-in shaft, and during that operation revolves of necessity at a variable speed given to it by the scrolls. In this way the carriage is kept parallel to the roller beam throughout its course, and comes up to the back stops along its entire length at one time.
(316) The arrangements for taking-in having thus been described, it now becomes necessary to describe the operation of winding. Before doing so, it will be better to deal with the problem to be solved, and it will aid in understanding it if the construction and method of building the cop be described. For this purpose a reference to the diagrams given in Figs.163and164, page 207, is necessary. The cop is built, as before explained, upon the blade or taper part of the spindle, and, when finished, is of the shape shown in Fig.163, viz., a cylinder with conical ends. The central part of the cop,E G K F, is cylindrical, and at the top and bottom of this part are two cones. The lower cone,A E B C F D, forms what is known as the “cop bottom,” and the upper one,G H I K, the “nose,” although the latter term is more often and strictly applied to the extreme apex at the pointsH I. As previously stated, the yarn may be wound either upon the bare spindle, upon a short paper tube, as indicated by the thick line inside the cop bottom, or upon a similar tube the whole length of the cop. The use of paper tubes of this character is preferable, especially in cases where the cop is likely to be much handled, as it prevents it from being crushed in, and enablesthe introduction of a skewer for subsequent winding without there being any danger of the cop being pierced or “stabbed,” this being a fruitful source of waste.
(317) In commencing to wind, the yarn is wrapped on the lower part of the spindle in close coils or spirals for a length of a little more than an inch. The whole of one stretch is wrapped upon this space, and when the next stretch requires winding, it is laid upon the previous layer, and so on until the double coneA E B C F Dis produced. The length of the traverse of the winding faller wire, or the length of each layer vertically, is called the “chase” of the cop or faller. From this point the yarn is wound in successive layers, beginning always at a higher point, until the final traverse is obtained by which the winding is conducted upon the surface or nose represented by the lettersG H I K. It was stated in paragraph 311 that the winding faller wire, when the winding faller is locked, is in a position a little below the pointH I. As soon as the carriage begins to run in, the vertical movement of the winding faller locking lever begins, and is so arranged that the first movement of the wire is a rapid downward one. The effect is that the yarn is laid on the nose of the cop in coarsely-pitched descending spirals, as shown in Fig.164, these extending downwards until the winding faller wire reaches a point opposite the base of the upper cone, in this case shown in Fig.163atK. From this point a slower ascent of the winding faller wire is made, so that the yarn is laid in the more finely pitched spirals shown, until the nose of the cop is reached. By this time the carriage has arrived at the roller beam, and the whole of the 63 inches of yarn has been wound.
(318) When the first layer of yarn is wound, and the winding faller is assuming its position to wrap on the second, the initial point of its traverse is a little raised. In this way the yarn is gradually wound in layers, which are represented by the angular lines springing from the linesA EandD Ftowards the spindles. During this period the enlargement of the diameter of the cop bottom is proceeding until at the pointsE Fthe full diameter of the cop is reached. As soon as this occurs the initial point of each layer is gradually raised, and the length of the traverse is slowly diminished as the completion of building is approached, until at the termination of a cop the angle of the layers is shown by the linesG HandI K. There are thus two adjustments shown to be necessary—first, the starting point of each traverse of the winding faller requires altering; and second, its extent also needs regulation.
(319) These two objects are attained by the regulation of the copping railP, as shown in Fig.161. The ends of this rail rest upon inclined “copping” platesY X, which are fastened together by the rodW, and which receive, as will afterwards be described, an inward movement during the building of the cop. It was shown that the locking of the faller lever and its vertical movement leads to a corresponding movement of the faller. If, for instance, the faller locking lever fell an inch, the winding faller sector would be oscillated and the faller wire drawn upwards. The rate of the ascent of the latter is absolutely relative to the period of the descent of the locking lever. Referring now to Fig.165, which is a small diagrammatic sketch of the copping rail and its supports, suppose the lineG Hto represent the top of former,O Pthe latter, andLthe bowl at the foot of the locking lever, ifL, starting from the left hand position, be supposed to travel in the direction of the arrowV, it will be seen that it will fall to the extent indicated by the spaceY Z. If, on the other hand, the slidesO Pare moved into the position shown by the dotted lines, the railG Hwill also fall into that indicated in a similar manner. The result is that ifLnow makes the same traverse as before it will rise a little as indicated by the spaceW X. The effect on the winding faller would be that in the first case it would be raised, and in the second it would be depressed to an extent corresponding to the depression of the locking lever. The extent to which this elevation or depression is made depends upon the vertical traverse of the locking lever, and the ratio of the distance of the point of junction of the sectorCwith the faller shaft and that of the faller wire from the same rod. If, for instance, this proportion was 1:2, an elevation of the locking lever half an inch would result in a depression of the faller an inch. It is therefore necessary, during the inward run of the carriage, to provide for the inclination of the carriage to such an extent as to secure the requisite traverse of the faller wire. As the amount of such traverse varies during the building of the cop, it follows that the inclination of the copping rail must be varied correspondingly.
Fig. 165.J.N.
Fig. 165.J.N.
(320) Referring again to Fig.161, the ends of the copping rails have pins fixed in them, on which are anti-friction bowls, which run upon the edges of the copping plates. The latter are duplicated, so as to sustain the rail at each side, and thus maintain its vertical position. At one side of one of the platesYis an earS1, which is threaded to correspond with a square threaded screwSpassing through a fixed bracket fastened to the floor. In this way the screwSis free to revolve, but cannot make any longitudinal movement. On the end of the screwSa ratchet wheel is fixed with which a pawlS2engages, which is oscillated so as to move the wheel one tooth at convenient times. The speed of the revolution of the screw varies according to the counts being spun, the elevation of the point of locking being more quickly effected when coarse yarns are being made than when the finer varieties are produced. Whatever may be the velocity at which this elevation is accelerated, the profile of the copping plates is such that the inner end of the copping railPis lowered at a more rapid rate during the formation of the cop bottom than at a subsequent stage. The reason of this will be easily comprehended, if the description of the mode of building the latter be borne in mind. It was then shown that the traverse of the winding faller rapidly increased in extent until the full length of the cop bottom was built. It, therefore, follows that the descent of the locking lever must be largely increased at this period at a quick rate, in order to produce the result indicated. When the outer end of the copping rail begins to descend at a rate which more nearly corresponds to that of the inner end, it gradually approaches to the horizontal, and the vertical motion of the slide, locking lever, and faller is proportionately limited.
(321) The regulation of the winding faller as just described was the one which was usual until recent years. It has been found necessary, however, to obtain a more accurate regulation, so as to ensure that the faller wire shall be in its correct position when locking occurs, especially during the period between the beginning of a cop and the attainment of its full diameter. It is now customary to attach to the front end of the copping rail a loose plateQ, which is hinged at one end to the rail, and which carries at its outer extremity a pin and bowl resting upon a third inclined plateZ. By varying the profile of the plateZ, the regulation of the faller during the early part of its traverse can be accurately made and the proper position of the wire ensured. As a glance at the illustration will show, the upper edge of the copping rail is not straight, but is shaped so as to give a variable speed to the slideLin its vertical movement. The proper shaping of the copping rail gave rise to some difficulty, and it will be seen that the loose copping railQis shaped so as to produce the proper effect, while being much more easily adjusted.
Fig. 161.J.N.
Fig. 161.J.N.
(322) The actual operation of this mechanism is as follows: When the carriage is at its outermost point, and the winding faller is locked, the wire is, as previously mentioned, a little below the nose of the cop. As the inward run proceeds, the bowl first runs up the loose incline, thus raising the locking lever and depressing the winding faller wire. The distance, from the extreme outward point reached by the bowlL1and that where the loose railQis hinged and the downward inclination of the copping rail begins, is so short that the initial depression of the winding faller is very rapid. This produces the coarsely pitched coils referred to in paragraph 317, and illustrated in Fig.164. By the time the bowlL1is at its highest point the winding faller wire is opposite the base of the upper cone. The subsequent downward inclination of the copping rail is much less acute, and the consequent descent of the faller locking lever less rapid. As a result the upward traverse ofthe winding faller wire is made more slowly, and the yarn is wound in more finely pitched spirals. It only remains to be said, in connection with this part of the subject, that owing to the shape of the copping plates their inward movement is accompanied by a gradual fall of the copping rail, and, consequently, the locking point of the faller lever is relatively elevated. In other words, the traverse of the locking lever prior to locking is gradually lessened as the trail lever slideLis lowered, and this is equivalent to an elevation of the winding faller lever and its locking point or shoulderK. This causes the depression of the winding faller wire prior to locking to be gradually diminished, so that there is an elevation of its initial point.
(323) The method of obtaining the traverse of the winding faller having been described, the equally important points relating to the mode of rotating the spindle during winding require to be dealt with. A little thought will show that so long as the surface upon which the yarn is wound remains small the spindles must revolve at a more rapid rate than when the surface is enlarged. As the extreme diameter of the cop bottom is enlarged the conditions of successful winding are continually changing. At the commencement of the cop the yarn is wound upon what is practically a parallel surface with a diameter of5⁄16inch and a circumference of ·98 inch. This implies that to wind the 63 inches of yarn 64·3 revolutions are required, these being made during the run up of the carriage. But as the diameter of the cop is enlarged the circumference of the conical surface becomes a variable one, and owing to its enlargement the number of revolutions required to wind the same length of yarn is fewer. This is quite clear and needs no demonstration. Thus when the cop bottom is formed the extreme range of variation is reached, and it follows that in the interval between the commencement of winding and the formation of the cop bottom each stretch must be accompanied by a diminution of the velocity of the spindle proportionate to the increase of diameter. In addition to this it is necessary to take into consideration the varying diameter of the conical surface on which winding takes place, which necessitates a greater terminal than initial velocity of the spindle.
Figs. 163 and 164.J.N.
Figs. 163 and 164.J.N.
(324) A further point requires elucidation. If the spindle blade were parallel, the number of revolutions necessary to wind the 63 inches of yarn properly, when the cop bottom is formed, being fixed, no further alteration would be necessary. But these conditions do not exist, and the nose of the cop is wound upon a continually diminishing diameter. It is of the utmost importance that the yarn is wound tightly at the nose during the whole of the building of the cop. The rate of the vertical traverse being practically uniform, unless an acceleration of the spindle velocity occurred, there would be slack winding during the latter part of the building of the cop. This would produce a sponginess of the nose, which, when the yarn was drawn off in the subsequent process of winding, as shown by the arrow in Fig.164, would result in several rings or coils being pulled out in an entangled condition, thus producing waste. Technically the cop would be said to be “halched.” Illustrating this part of the subject by figures, if the diameter of the spindle at the pointB, Fig.163, be assumed to be1⁄4inch, its circumference would be ·7854 inch; while if the diameter atHbe assumed to be1⁄8inch, the circumference would be only ·3927 inch. To wind, say, 10 inches of yarn in each case, would require about 12 and 25 revolutions of the spindle respectively. It is therefore clear that, if the same length is to be wound with equal tension upon the nose of the copthroughout the whole process of building, there must be a gradual acceleration of the terminal velocity of the spindle. Although this is only slight at first it is required at an earlier point as the cop is formed, and becomes of increasing importance.
Fig. 166.J.N.
Fig. 166.J.N.
(325) It will be shown, a little later, that the rotation of the spindles during winding is obtained by the pull of the carriage on a chain, which has its other end attached to an oscillating arm, being fastened to a drum on the carriage. To get a clear idea of the action of this part of the mechanism the two diagrams shown in Figs.166and167are given, a study of which will be profitable. In Fig.166the circlesB C Drepresent three positions of the barrel or drum after it has moved in a horizontal plane in the direction of the arrow. To the drum a chain is supposed to be attached, which is held at the pointA. It is, of course, understood that the barrel is mounted upon a shaft or axis so that it can freely revolve. If it be now assumed that the barrel is in the left hand of the three positionsB, the chain will be wrapped completely round it. As it is moved horizontally in the direction of the arrow it is revolved, as indicated by the curved arrows, and, by the time it has reached its middle positionC, has been rotated sufficiently to unwind about half a turn of the chain. A further horizontal motion to the right hand positionDwill complete the unwinding, and, by this time, the drum will have made one complete revolution. It will be at once seen that the rate at which the drum will be revolved will depend upon two factors—its diameter, and the speed of its horizontal traverse. If the pointAat which the chain is held is stationary, and the horizontal movement uniform, then the rotation of the barrel will be constant. But if the barrel be traversed at a variable rate then its rotation will also be variable. In actual practice this uniformity does not exist, for, as was shown in paragraph 315, the taking-in scrolls vary considerably in diameter. Assuming this variation to be 1:3:1, it would follow that the rotation of the barrel would increase and diminish in thesame ratio. In practice this is what happens, and the speed of the revolution of the barrel is quicker about the middle of the taking-in than at any other time.
(326) The assumption that the pointAis stationary was only made to illustrate the point at issue, and is not founded upon the actual facts of the case. If now it be assumed that not only the barrel but the point at which the chain is held makes a forward movement, a new set of conditions arises. In this case the unwinding of the chain during a given time will be diminished by the amount of the advance of the pointAin the same period. Assuming the latter to be made at a regular rate it would be easy to calculate the extent of the unwinding. If the effect of the horizontal movement of the barrel fromBtoCbe to unwind half of one coil of chain—say a length of 7 inches—and that in the same space of time the pointAmoved 3 inches, the amount unwound would be reduced to 4 inches. But this is not the actual condition of things in practice. The point moves at a variable velocity, its forward motion gradually diminishing, so that the acceleration of the rotary velocity of the barrel is greater at the end of its horizontal traverse than at the beginning. In other words, its terminal velocity is highest.
(327) The point of the attachment of the chain atAis made in an oscillating arm which, during the inward run of the carriage, receives a forward movement at a speed which is controlled by the velocity of the back shaft. As the latter is, in turn, commanded by the scroll shaft during this period—see paragraph315—it follows that the variation in the forward movement of the arm is coincident with that of the carriage. Thus the advance of the pointAwill always be in strict correspondence with the velocity of the carriage traverse.
(328) Referring now to Fig.167, and, assumingA Bto be the arm to which the chain is fastened, andO JandH Cto represent the arcs through which the point of attachment of the chain travels at different times, it will be seen that the periods of movement are well marked. In each case the arcs are of the same number of degrees, although the chord of one is shorter than that of the other. Dealing first with the inner arc, which represents the position of the point of attachment when nearer the centre, the whole period of movement is divided into equal parts. These are represented by the lettersJ K L M N O. Now, if vertical lines are drawn from these, until they terminate in a straight line drawn parallel to a horizontal line through the pointB, a clear idea can be formed of the effect of the oscillation of the vertical armA B. The lines terminate atJ1K1L1M1N1O1. It can be easily seen that the horizontal movement of the point of attachment of the chain gradually becomes less as the arm is oscillated from its most backward positionB Cto its most forward oneB H, this diminution occurring most after the pointLis reached. In the movement fromJtoKandKtoLthe horizontal traverse is about equal. It shows a decrease fromLtoM, a greater one fromMtoN, and a still greater one fromNtoO. The same thing happens if the chain be supposed to be attached at the pointD. In this case also the decrease in the horizontal forward traverse is variable, but occurs in the same way. The periods here are marked by the lettersCtoH, and the extent of the forward motion by thoseC1toH1. It will be noticed that the amount of the traverse is greater than that previously noted, the total space covered being respectivelyJ1toO1andC1toH1. That is to say, the point at which the chain is fastened moves forward in the same direction asthe barrel, but at a different speed. In other words, when the chain is held atK, the total forward movement is comparatively small, and if it were held at a point shown by the small inner circle, it would be still less. On the other hand, its attachment atBimplies a greater total forward movement. It therefore happens that the retardation of the chain by the arm is less in the early part of the oscillation ofA B—or, to put it differently, the delivery of the winding chain by the arm is greater when it is fixed atDthan when it is fixed atK. Therefore the barrel is more slowly rotated during the same period in the former than in the latter case, but as it completes its lateral movement it is rapidly and considerably accelerated.
(329) The application of this principle is as follows, and it can now be stated that the end of the chain is attached to a nut which slides along the arm, being actuated by the rotation of a screw upon which it fits. Remembering that an acceleration of the terminal velocity and a regulation of the revolution of the spindle is required, the demonstration just given shows that these are obtained by the removal of the nut further from the centre of oscillation. The influence of the pull of the chain upon the barrel when the nut is in the positionKis much slighter, and shows less variation than when it is atD. Every inch which the nut travels outwards has an influence upon this factor, and the conditions of winding are thus accurately regulated. When the winding of the cop begins, the nut is in its lowest position, and the rotation of the barrel is then practically equal. As the nut moves away from the centre the barrel gradually rotates more slowly at the beginning of its inward movement. By the time the most outward position is reached—which, in practice, coincides with the formation of the cop bottom—the variation in the velocity has reached its greatest amount. This, it can be easily seen, is what is wanted. Referring again to Fig.163, one revolution of the spindle when the yarn is being wound onA Dwould practically take up the same length as would be taken up at the top of the paper tube. But when the faller is guiding the yarn on the conical surface fromEtoB, one revolution of the spindle would wind on a greater length atEthan it would atB. Therefore, the initial velocity requires to be less than the terminal. But when the pointEhas become the initial position, the conditions of winding remain thereafter constant, except in so far as is affected by the taper of the blade, and there is no further need for an outward movement of the nut.
(330) The theory underlying the method of winding having thus been dealt with, the mechanism employed can be described. This is shown in Fig.168, which is a diagram of the whole of the apparatus, and in Fig.169, which is an enlarged view of a portion of it. The winding armMis centered at its lower end, and has formed on it a toothed quadrantM1. The “quadrant”Moscillates on a short shaft, securely carried by the headstock framing, and receives its forward movement by means of a pinionZ, which engages with its teeth. The extent of the quadrant movement is about a quarter circle. The pinionZis mounted on the same centre as a grooved pulley, over which a cord from the back shaftHis passed. Thus the rotation ofHin either direction produces a similar movement in the pinionZ; and the effect is, that, while the back shaft is drawing the carriage out, the pinion is revolving so as to raise the armMor cause it to make a backward oscillation. When the back shaft acts as a taking-in shaft, as described in paragraph 315, the pinionZis revolved so as to move the armMforward. The velocity at which the forward stroke ismade is by this arrangement a variable one, and completely corresponds to that of the carriage traverse. Inside the winding arm a long slot is formed in which a screwPis placed, this being free to revolve. It may be made with a thread of equal pitch throughout, but, as shown, is provided with a thread of varying pitch, which gradually becomes finer towards the outward end of the arm. The reason of this is obvious. The effect of each layer of yarn upon the problem of winding is greater at the beginning of the formation of the cop bottom than when it is more nearly finished. That is, the enlargement of its diameter is relatively greater at the first stage than at any other. For instance, if the diameter is3⁄8inch and it be increased1⁄16inch, the ratio is1⁄6th; while if the diameter is3⁄4inch, and the same increase takes place, the ratio is1⁄12th only. The variation required in the speed of winding as each layer is wrapped is therefore less in the latter than in the former case. This is the purpose of the helical screw, which gives a quicker advance to the nut in the earlier stages of winding than when the cop bottom is nearly formed.