Fig. 194Fig. 194.
Fig. 194.
“InFig. 194,a aandb bare centre lines passing through the major and minor axes of the ellipse, of whichais the axis or centre,b cis the major anda ehalf of the minor axis. Draw the rectangleb f g c, and then the diagonal lineb e; at a right angle tob edraw linef hcuttingb bati. With radiusa eand fromaas a centre draw the dotted arce j, giving the pointjon the lineb b. From centrek, which is on lineb b, and central betweenbandj, draw the semicircleb m j, cuttinga aatl. Draw the radius of the semicircleb m jcuttingf gatn. With radiusm nmark ona a, at and fromaas a centre, the pointo. With radiush oand from centrehdraw the arcp o q. With radiusa land frombandcas centres draw arcs cuttingp o qat the pointsp q. Draw the linesh p randh q s, and also the linesp i tandq v w. Fromhas centre draw that part of the ellipse lying betweenrands. With radiusp rand frompas a centre draw that part of the ellipse lying betweenrandt. With radiusq sand fromqdraw the ellipse fromstow. With radiusi tand fromias a centre draw the ellipse fromttob. With radiusv wand fromvas a centre draw the ellipse fromwtoc, and one half the ellipse will be drawn. It will be seen that the whole construction has been performed to find the centresh p q iandv, and that whilevandimay be used to carry the curve around the other side or half of the ellipse, new centres must be provided forh pandq; these new centres correspond in position toh p q.
“If it were possible to subdivide the ellipse into equal parts it would be unnecessary to resort to these processes of approximately representing the two curves by arcs of circles; but unless this be done, the spacing of the teeth can only be effected by the laborious process of stepping off the perimeter into such small subdivisions that the chords may be regarded as equal to the arcs, which after all is but an approximation; unless, indeed, we adopt the mechanical expedient of cutting out the ellipse in metal or other substance, measuring and subdividing it with a strip of paper or a steel tape, and wrapping back the divided measure in order to find the points of division on the curve.
Fig. 195Fig. 195.
Fig. 195.
“But these circular arcs may be rectified and subdivided withgreat facility and accuracy by a very simple process, which we take from Prof. Rankine’s “Machinery and Mill Work,” and is illustrated inFig. 195. Leto bbe tangent atoto the arco d, of whichcis the centre. Draw the chordd o, bisect it ine, and produce it toa, makingo a=o e; with centreaand radiusa ddescribe an arc cutting the tangent inb; theno bwill be very nearly equal in length to the arco d, which, however, should not exceed about 60°; if it be 60°, the error is theoretically about1⁄900of the length of the arc,o bbeing so much too short; but this error varies with the fourth power of the angle subtended by the arc, so that for 30° it is reduced to1⁄16of that amount, that is, to1⁄14400. Conversely, leto bbe a tangent of given length; makeo f=1⁄4o b; then with centrefand radiusf bdescribe an arc cutting the circleo d g(tangent too bato) in the pointd; theno dwill be approximately equal too b, the error being the same as in the other construction and following the same law.
Fig. 196Fig. 196.
Fig. 196.
“The extreme simplicity of these two constructions and the facility with which they may be made with ordinary drawing instruments make them exceedingly convenient, and they should be more widely known than they are. Their application to the present problem is shown inFig. 196, which represents a quadrant of an ellipse, the approximate arcsc d,d e,e f,f ahaving been determined by trial and error. In order to space this off, for the positions of the teeth, a tangent is drawn atd, upon which is constructed the rectification ofd c, which isd g, and also that ofd ein the opposite direction, that is,d h, by the process just explained. Then, drawing the tangent atf, we set off in the same mannerf i=f e, andf k=f a, and then measuringh l=i k, we have finallyg l, equal to the whole quadrant of the ellipse.
“Let it now be required to lay out 24 teeth upon this ellipse; that is, 6 in each quadrant; and for symmetry’s sake we will suppose that the centre of one tooth is to be ata, and that of another atc,Fig. 196. We therefore dividel ginto six equal parts at the points 1, 2, 3, &c., which will be the centres of the teeth upon the rectified ellipse. It is practically necessary to make the spaces a little greater than the teeth; but if the greatest attainable exactness in the operation of the wheel is aimed at, it is important to observe that backlash, in elliptical gearing, has an effect quite different from that resulting in the case of circular wheels. When the pitch-curves are circles, they are always in contact; and we may, if we choose, make the tooth only half the breadth of the space, so long as its outline is correct. When the motion of the driver is reversed, the follower will stand still until the backlash is taken up, when the motion will go on with a perfectly constant velocity ratio as before. But in the ease of two elliptical wheels, if the follower stand still while the driver moves, which must happen when the motion is reversed if backlash exists, the pitch-curves are thrown out of contact, and, although the continuity of the motion will not be interrupted, the velocity ratio will be affected. If the motion is never to be reversed, the perfect law of the velocity ratio due to the elliptical pitch-curve may be preserved by reducing the thickness of the tooth, not equally on each side, as is done in circular wheels, but wholly on the side not in action. But if the machine must be capable of acting indifferently in both directions, the reduction must be made on both sides of the tooth: evidently the action will be slightly impaired, for which reason the backlash should be reduced to a minimum. Precisely whatisthe minimum is not so easy to say, as it evidently depends much upon the excellence of the tools and the skill of the workmen. In many treatises on constructive mechanism it is variously stated that the backlash should be from one-fifteenth to one-eleventh of the pitch, which would seem to be an ample allowance in reasonably good castings not intended to be finished, and quite excessive if the teeth are to be cut; nor is it very obvious that its amount should depend upon the pitch any more than upon the precession of the equinoxes. On paper, at any rate, we may reduce it to zero, and make the teeth and spaces equal in breadth, as shown in the figure, the teeth being indicated by the double lines. Those upon the portionl hare then laid off uponk i, after which these divisions are transferred to curves. And since under that condition the motion of this third line, relatively to each of the others, is the same as though it rolled along each of them separately while they remained fixed, the process of constructing the generated curves becomes comparatively simple. For the describing line, we naturally select a circle, which, in order to fulfil the condition, must be small enough to roll within the pitch ellipse; its diameter is determined by the consideration, that if it be equal toa p, the radius of the arca f, the flanks of the teeth in that region will be radial. We have, therefore, chosen a circle whose diameter,a b, is three-fourths ofa p, as shown, so that the teeth, even at the ends of the wheels, will be broader at the base than on the pitch line. This circle ought strictly to roll upon the true elliptical curve, and assuming as usual the tracing-point upon the circumference, the generated curves would vary slightly from true epicycloids, and no two of those used in the same quadrant of the ellipse would be exactly alike. Were it possible to divide the ellipse accurately, there would be no difficulty in laying out these curves; but having substituted the circular arcs, we must now roll the generating circle upon these as bases, thus forming true epicycloidal teeth, of which those lying upon the same approximating arc will be exactly alike.Should the junction of two of these arcs fall within the breadth of a tooth, as atd, evidently both the face and the flank on one side of that tooth will be different from those on the other side; should the junction coincide with the edge of a tooth, which is very nearly the case atf, then the face on that side will be the epicycloid belonging to one of the arcs, its flank a hypocycloid belonging to the other; and it is possible that either the face or the flank on one side should be generated by the rolling of the describing circle partly on one arc, partly on the one adjacent, which, upon a large scale and where the best results are aimed at, may make a sensible change in the form of the curve.
Fig. 197Fig. 197.
Fig. 197.
“The convenience of the constructions given inFig. 194is nowhere more apparent than in the drawing of the epicycloids, when, as in the case in hand, the base and generating circles may be of incommensurable diameters; for which reason we have, inFig. 197, shown its application in connection with the most rapid and accurate mode yet known of describing those curves. Letcbe the centre of the base circle;bthat of the rolling one;athe point of contact. Divide the semi-circumference ofbinto six equal parts at 1, 2, 3, &c.; draw the common tangent ata, upon which rectify the arca2by process No. 1, then by process No. 2 set out an equal arca2on the base circle, and stepping it off three times to the right and left, bisect these spaces, thus making subdivisions on the base circle equal in length to those on the rolling one. Take in succession as radii the chordsa1,a2,a3, &c., of the describing circle, and with centres 1, 2, 3, &c., on the base circle, strike arcs either externally or internally, as shown respectively on the right and left; the curve tangent to the external arcs is the epicycloid, that tangent to the internal ones the hypocycloid, forming the face and flank of a tooth for the base circle.
Fig. 198Fig. 198.
Fig. 198.
“In the diagram,Fig. 196, we have shown a part of an ellipse whose length is 10 inches and breadth 6, the figure being half size. In order to give an idea of the actual appearance of the combination when complete, we show inFig. 198the pair in gear, on a scale of 3 inches to the foot. The excessive eccentricity was selected merely for the purpose of illustration.Fig. 198will serve also to call attention to another serious circumstance, which is that although the ellipses are alike, the wheels are not; nor can they be made so if there be an even number of teeth, for the obvious reason that a tooth upon one wheel must fit into a space on the other; and since in the first wheel,Fig. 196, we chose to place a tooth at the extremity of each axis, we must in the second one place there a space instead; because at one time the major axes must coincide, at another the minor axis, as inFig. 191. If then we use even numbers, the distribution and even the forms of the teeth are not the same in the two wheels of the pair. But this complication may be avoided by using an odd number of teeth, since, placing a tooth at one extremity of the major axis, a space will come at the other.
Fig. 199Fig. 199.
Fig. 199.
“It is not, however, always necessary to cut teeth all round these wheels, as will be seen by an examination ofFig. 199,canddbeing the fixed centres of the two ellipses in contact atp. Nowpmust be on the linec d, whence, considering the free foci, we seep bis equal top c, andp atop d; and the common tangent atpmakes equal angles withc pandp a, as is also withp bandp d; therefore,c dbeing a straight line,a bis also a straight line and equal toc d. If then the wheels be overhung, that is, fixed on the ends of the shafts outside the bearings, leaving the outer faces free, the moving foci may be connected by a rigid linka b, as shown.
“This link will then communicate the same motion that would result from the use of the complete elliptical wheels, and we may therefore dispense with most of the teeth, retaining only those near the extremities of the major axes which are necessary in order to assist and control the motion of the link at and near the dead-points. The arc of the pitch-curves through which the teeth must extend will vary with their eccentricity: but in many cases it would not be greater than that which in the approximation may be struck about one centre, so that, in fact, it would not be necessary to go through the process of rectifying and subdividing the quarter of the ellipse at all, as in this case it can make no possible difference whether the spacing adopted for the teeth to be cut would “come out even” or not if carried around the curve. By this expedient, then, we may save not only the trouble of drawing, but a great deal of labor in making, the teeth round the whole ellipse. We might even omit the intermediate portions of the pitch ellipses themselves; but as they move in rolling contact their retention can do no harm, and in one part of the movement will be beneficial, as they will do part of the work; for if, when turning, as shown by the arrows, we consider the wheel whose axis isdas the driver, it will be noted that its radius of contact,c p, is on the increase; and so long as this is the case the other wheel will be compelled to move by contact of the pitch lines, although the link be omitted. And even if teeth be cut all round the wheels, this link is a comparatively inexpensive and a useful addition to the combination, especially if the eccentricity be considerable. Of course the wheels shown inFig. 198might also have been made alike, by placing a tooth at one end of the major axis and a space at the other, as above suggested. In regard to the variation in the velocity ratio, it will be seen, by reference toFig. 199, that ifdbe the axis of the driver, the follower will in the position there shown move faster, the ratio of the angular velocities beingpd/pb; if the driver turn uniformly the velocity ofthe follower will diminish, until at the end of half a revolution, the velocity ratio will bepb/pd; in the other half of the revolution these changes will occur in a reverse order. Butp d=l b; if then the centresb dare given in position, we knowl p, the major axis; and in order to produce any assumed maximum or minimum velocity ratio, we have only to dividel pinto segments whose ratio is equal to that assumed value, which will give the foci of the ellipse, whence the minor axis may be found and the curve described. For instance, inFig. 198the velocity ratio being nine to one at the maximum, the major axis is divided into two parts, of which one is nine times as long as the other; inFig. 199the ratio is as one to three, so that, the major axis being divided into four parts, the distancea cbetween the foci is equal to two of them, and the distance of either focus from the nearer extremity of the major axis equal to one, and from the more remote extremity equal to three of these parts.”
Fig. 200Fig. 200.
Fig. 200.
Another example of obtaining a variable motion is given inFig. 200. The only condition necessary to the construction of wheels of this class is that the sum of the radii of the pitch circles on the line of centres shall equal the distance between the axes of the two wheels. The pitch curves are to be considered the same as pitch circles, “so that,” says Willis, “if any given circle or curve be assumed as a describing (or generating) curve, and if it be made to roll on the inside of one of these pitch curves and on the outside of the corresponding portion of the other pitch curve, then the motion communicated by the pressure and sliding contact of one of the curved teeth so traced upon the other will be exactly the same as that effected by the rolling contact (by friction) of the original pitch curves.”
It is obvious that onbthe corner sections are formed of simple segments of a circle of which the centre is the axis of the shaft, and that the sections between them are simply racks. The corners ofaare segments of a circle of which the axis ofais the centre, and the sections between the corners curves meeting the pitch circles of the rack at every point as it passes the line of centres.
Fig. 201Fig. 201.
Fig. 201.
Intermittent motion may also be obtained by means of a worm-wheel constructed as inFig. 201, the worm having its teeth at a right angle to its axis for a distance around the circumference proportioned to the required duration of the period of rest; or the motion may be made variable by giving the worm teeth different degrees of inclination (to the axis), on different portions of the circumference.
In addition to the simple operation of two or more wheels transmitting motion by rotating about their fixed centres and in fixed positions, the following examples of wheel motion may be given.
Fig. 202Fig. 202.
Fig. 202.
InFig. 202are two gear-wheels,a, which is fast upon its stationary shaft, andb, which is free to rotate upon its shaft, the linkcaffording journal bearing to the two shafts. Suppose thatahas 40 teeth, whilebhas 20 teeth, and that the linkcis rotated once around the axis ofa, how many revolutions willbmake? By reason of there being twice as many teeth inaas inbthe latter will make two rotations, and in addition to this it will, by reason of its connection to the armc, also make a revolution, these being two distinct motions, one a rotation ofbabout the axis ofa, and the other two rotations ofbupon its own axis.
Fig. 203Fig. 203.
Fig. 203.
Fig. 204Fig. 204.
Fig. 204.
A simple arrangement of gearing for reversing the direction of rotation of a shaft is shown inFig. 203.iandfare fast and loose pulleys for the shaftd,aandcare gears free to rotate upond,nis a clutch driven byd; hence ifnbe moved so as to engage withcthe latter will act as a driver to rotate the shaftb, thewheel uponbrotatingain an opposite direction to the rotation ofd. But ifnbe moved to engage withathe latter becomes the driving wheel, andbwill be caused to rotate in the opposite direction. Since, however, the engagement of the clutchnwith the clutch on the nut of the gear-wheels is accompanied with a violent shock and with noise, a preferable arrangement is shown inFig. 204, in which the gears are all fast to their shafts, and the driving shaft forcpasses through the core or bore of that fora, which is a sleeve, so that when the driving belt acts upon pulleyfthe shaftbrotates in one direction, while when the belt acts upone,brotates in the opposite direction,ibeing a loose pulley.
If the speed of rotation ofbrequire to be greater in one direction than in the other, then the bevel-wheel onbis made a double one, that is to say, it has two annular toothed surfaces on its radial face, one of larger diameter than the other;agearing with one of these toothed surfaces, andcwith the other. It is obvious that the pinionsa c, being of equal diameters, that gearing with the surface or gear of largest diameter will give tobthe slowest speed of rotation.
Fig. 205Fig. 205.
Fig. 205.
Fig. 205represents Watt’s sun-and-planet motion for converting reciprocating into rotary motion;b dis the working beam of the engine, whose centre of motion is atd. The gearais so connected to the connecting rod that it cannot rotate, and is kept in gear with the wheelcon the fly-wheel shaft by means of the link shown. The wheelabeing prevented from rotation on its axis causes rotary motion to the wheelc, which makes two revolutions for one orbit ofa.
Fig. 206Fig. 206.
Fig. 206.
An arrangement for the rapid increase of motion by means of gears is shown inFig. 206, in whichais a stationary gear,bis free to rotate upon its shaft, and being pivoted upon the shaft ofa, atd, is capable of rotation aroundawhile remaining in gear withc. Suppose now that the wheelawere absent, then ifbwere rotated aroundcwithdas a centre of motion,cand its shaftewould make a revolution even thoughbwould have no rotation upon its axis. Butawill causebto rotate upon its axis and thus communicate a second degree of motion toc, with the result that one revolution ofbcauses two rotations ofc.
Fig. 207Fig. 207.
Fig. 207.
The relation of motion betweenbandcis in this case constant (2 to 1), but this relation may be made variable by a construction such as shown inFig. 207, in which the wheelbis carried in a gear-wheelh, which rides upon the shaftd. Suppose now thathremains stationary whilearevolves, then motion will be transmitted throughbtoc, and this motion will be constant and in proportion to the relative diameters ofaandc. But suppose by means of an independent pinion the wheelhbe rotated upon its axis, then increased motion will be imparted toc, and the amount of the increase will be determined by the speed of rotation ofh, which may be made variable by means of cone pulleys or other suitable mechanical devices.
Fig. 208Fig. 208.
Fig. 208.
Fig. 208represents an arrangement of gearing used upon steam fire-engines and traction engines to enable them to turn easily in a short radius, as in turning corners in narrow streets. The object is to enable the driving wheel on either side of the engine to increase or diminish its rotation to suit the conditions caused by the leading or front pair of steering wheels.
In the figuresais a plate wheel having the lugsl, by means of which it may be rotated by a chain.ais a working fit on the shafts, and carries three pinionsepivoted upon their axesp.fis a bevel-gear, a working fit ons, whilecis a similar gear fast tos. The pinionsb,dare to drive gears on the wheels of the engine, the wheels being a working fit on the axle. Let it now be noted that ifsbe rotated,candfwill rotate in opposite directions andawill remain stationary. But ifabe rotated, then all the gears will rotate with it, butewill not rotate uponpunless there be an unequal resistance to the motion of pinionsdandb. So soon, however, as there exists an inequality of resistance betweendandbthen pinionseoperate. For example, letbhave more resistance thand, andbwill rotate more slowly, causing pinioneto rotate and movecfaster than is due to the motion of the chain wheela, thus causing the wheel on one side of the engine to retard and the other to increase its motion, and thus enable the engine to turn easily. From its action this arrangement is termed the equalizing gear.
InFigs. 209to214are shown what are known as mangle-wheels from their having been first used in clothes mangling machines.
Fig. 209Fig. 209.
Fig. 209.
The mangle-wheel[10]in its simplest form is a revolving disc of metal with a centre of motionc(Fig. 209). Upon the face of the disc is fixed a projecting annulusa m, the outer and inner edges of which are cut into teeth. This annulus is interrupted atf, and the teeth are continued round the edges of the interrupted portion so as to form a continued series passing from the outer to the inner edge and back again.
[10]From Willis’s “Principles of Mechanism.”
[10]From Willis’s “Principles of Mechanism.”
A pinionb, whose teeth are of the same pitch as those of the wheel, is fixed to the end of an axis, and this axis is mounted so as to allow of a short travelling motion in the directionb c. This may be effected by supporting this end of it either in a swing-frame moving upon a centre as atd, or in a sliding piece, according to the nature of the train with which it is connected. A short pivot projects from the centre of the pinion, and this rests in and is guided by a grooveb sf t b hk, which is cut in the surface of the disc, and made concentric to the pitch circles of the inner and outer rays of teeth, and at a normal distance from them equal to the pitch radius of the pinion.
Now when the pinion revolves it will, if it be on the outside, as inFig. 209, act upon the spur teeth and turn the wheel in the opposite direction to its own, but when the interrupted portionfof the teeth is thus brought to the pinion the groove will guide the pinion while it passes from the outside to the inside, and thus bring its teeth into action with the annular or internal teeth. The wheel will then receive motion in the same direction as that of the pinion, and this will continue until the gapfis again brought to the pinion, when the latter will be carried outwards and the motion again be reversed. Thevelocity ratioin either direction will remain constant, but the ratio when the pinion is inside will differ slightly from the ratio when it is outside, because the pitch radius of the annular or internal teeth is necessarily somewhat less than that of the spur teeth. However, the change of direction is not instantaneous, for the form of the groovesf t, which connects the inner and outer grooves, is a semicircle, and when the axis of the pinion reachessthe velocity of the mangle-wheel begins to diminish gradually until it is brought to rest atf, and is again gradually set in motion fromftot, when the constant ratio begins; and this retardation will be increased by increasing the difference between the radius of the inner and outer pitch circles.
Fig. 210Fig. 210.
Fig. 210.
The teeth of a mangle-wheel are, however, most commonly formed by pins projecting from the face of the disc as inFig. 210. In this manner the pitch circles for the inner and outer wheels coincide, and therefore the velocity ratio is the same within and without, also the space through which the pinion moves in shifting is reduced.
Fig. 211Fig. 211.
Fig. 211.
This space may be still further reduced by arranging the teeth as inFig. 211, that is, by placing the spur-wheel within the annular or internal one; but at the same time the difference of the two velocity ratios is increased.
If it be required that the velocity ratio vary, then the pitch lines of the mangle-wheel must no longer be concentric.
Fig. 212Fig. 212.
Fig. 212.
Thus inFig. 212the groovek lis directed to the centre of the mangle-wheel, and therefore the pinion will proceed during this portion of its path without giving any motion to the wheel, and in the other lines of teeth the pitch radius varies, hence the angular velocity ratio will vary.
InFigs. 209,210, and211the curves of the teeth are readily obtained by employing the same describing circle for the whole ofthem. But when the formFig. 212is adopted, the shape of the teeth requires some consideration.
Every tooth of such a mangle-wheel may be considered as formed of two ordinary teeth set back to back, the pitch line passing through the middle. The outer half, therefore, appropriated to the action of the pinion on the outside of the wheel, resembles that portion of an ordinary spur-wheel tooth that lies beyond its pitch line, and the inner half which receives the inside action of the pinion resembles the half of an annular wheel that lies within the pitch circle. But the consequence of this arrangement is, that in both positions the action of the driving teeth must be confined to the approach of its teeth to the line of centres, and consequently these teeth must be wholly within their pitch line.
To obtain the forms of the teeth, therefore, take any convenient describing circle, and employ it to describe the teeth of the pinion by rolling within its pitch circle, and to describe the teeth of the wheel by rolling within and without its pitch circle, and the pinion will then work truly with the teeth of the wheel in both positions. The tooth at each extremity of the series must be a circular one, whose centre lies on the pitch line and whose diameter is equal to half the pitch.
Fig. 213Fig. 213.
Fig. 213.
If the reciprocating piece move in a straight line, as it very often does, then the mangle-wheelis transformed into amangle-rack(Fig. 213) and its teeth may be simply made cylindrical pins, which those of the mangle-wheel do not admit of on correct principle.bbis the sliding piece, andathe driving pinion, whose axis must have the power of shifting fromatoathrough a space equal to its own diameter, to allow of the change from one side of the rack to the other at each extremity of the motion. The teeth of the mangle-rack may receive any of the forms which are given to common rack-teeth, if the arrangement be derived from eitherFig. 210orFig. 211.
But the mangle-rack admits of an arrangement by which the shifting motion of the driving pinion, which is often inconvenient, may be dispensed with.
Fig. 214Fig. 214.
Fig. 214.
bbFig. 214, is the piece which receives the reciprocating motion, and which may be either guided between rollers, as shown, or in any other usual way;athe driving pinion, whose axis of motion is fixed; the mangle rackccis formed upon a separate plate, and in this example has the teeth upon the inside of the projecting ridge which borders it, and the guide-groove formed within the ring of teeth, similar toFig. 211.
This rack is connected with the piecebbin such a manner as to allow of a short transverse motion with respect to that piece, by which the pinion, when it arrives at either end of the course, is enabled by shifting the rack to follow the course of the guide-groove, and thus to reverse the motion by acting upon the opposite row of teeth.
The best mode of connecting the rack and its sliding piece is that represented in the figure, and is the same which is adopted in the well-known cylinder printing-engines of Mr. Cowper. Two guide-rodsk c,k care jointed at one endkkto the reciprocating piecebb, and at the other endccto the shifting-rack; these rods are moreover connected by a rodmmwhich is jointed to each midway between their extremities, so that the angular motion of these guide-rods round their centreskkwill be the same; and as the angular motion is small and the rods nearly parallel to the path of the slide, their extremitiesccmay be supposed to move at a right angle to that path, and consequently the rack which is jointed to those extremities will also move uponbbin a direction at a right angle to its path, which is the thing required, and admits of no other motion with respect tobb.
Fig. 215Fig. 215.
Fig. 215.
To multiply plane motion the construction shown inFig. 215is frequently employed.aandbare two racks, andcis a wheel between them pivoted upon the rodr. A crank shaft or leverdis pivoted ateand also (atp) tor. Ifdbe operatedctraverses alongaand also rotates upon its axis, thus giving toba velocity equal to twice that of the lateral motion ofc.
The diameter of the wheel is immaterial, for the motion ofbwill always be twice that ofc.
Fig. 216Fig. 216.
Fig. 216.
Friction gearing-wheels which communicate motion one to the other by simple contact of their surfaces are termed friction-wheels, or friction-gearing. Thus inFig. 216letaandbbe two wheels that touch each other atc, each being suspended upon a central shaft; then if either be made to revolve, it will cause the other to revolve also, by the friction of the surfaces meeting atc. The degree of force which will be thus conveyed from one to the other will depend upon the character of the surface and the length of the line of contact atc.
These surfaces should be made as concentric to the axis of the wheel and as flat and smooth as possible in order to obtain a maximum power of transmission. Mr. E. S. Wicklin states that under these conditions and proper forms of construction as much as 300 horse-power may be (and is in some of the Western States) transmitted.
In practice, small wheels of this class are often covered with some softer material, as leather; sometimes one wheel only is so covered, and it is preferred that the covered wheel drive the iron one, because, if a slip takes place and the iron wheel was the driver, it would be apt to wear a concave spot in the wood covered one, and the friction between the two would be so greatly diminished that there would be difficulty in starting them when the damaged spot was on the line of centre.
If, however, the iron wheel ceased motion, the wooden one continuing to revolve, the damage would be spread over that part of the circumference of the wooden one which continued while the iron one was at rest, and if this occurred throughout a whole revolution of the wooden wheel its roundness would not be apt to be impaired, except in so far as differences in the hardness of the wood and similar causes might effect.
“To select the best material for driving pulleys in friction-gearing has required considerable experience; nor is it certainthat this object has yet been attained. Few, if any, well-arranged and careful experiments have been made with a view of determining the comparative value of different materials as a frictional medium for driving iron pulleys. The various theories and notions of builders have, however, caused the application to this use of several varieties of wood, and also of leather, india-rubber, and paper; and thus an opportunity has been given to judge of their different degrees of efficiency. The materials most easily obtained, and most used, are the different varieties of wood, and of these several have given good results.
“For driving light machinery, running at high speed, as in sash, door, and blind factories, basswood, the linden of the Southern and Middle States (Tilia Americana) has been found to possess good qualities, having considerable durability and being unsurpassed in the smoothness and softness of its movement. Cotton wood (Populus monilifera) has been tried for small machinery with results somewhat similar to those of basswood, but is found to be more affected by atmospheric changes. And even white pine makes a driving surface which is, considering the softness of the wood, of astonishing efficiency and durability. But for all heavy work, where from twenty to sixty horse-power is transmitted by a single contact, soft maple (Acer rubrum) has, at present, no rival. Driving pulleys of this wood, if correctly proportioned and well built, will run for years with no perceptible wear.
“For very small pulleys, leather is an excellent driver and is very durable; and rubber also possesses great adhesion as a driver; but a surface of soft rubber undoubtedly requires more power than one of a less elastic substance.
“Recently paper has been introduced as a driver for small machinery, and has been applied in some situations where the test was most severe; and the remarkable manner in which it has thus far withstood the severity of these tests appears to point to it as the most efficient material yet tried.
“The proportioning, however, of friction-pulleys to the work required and their substantial and accurate construction are matters of perhaps more importance than the selection of material.
“Friction-wheels must be most accurately and substantially made and kept in perfect line so that the contact between the surfaces may not be diminished. The bodies are usually of iron lagged or covered with wooden segments.
“All large drivers, say from four to ten feet diameter and from twelve to thirty inch face, should have rims of soft maple six or seven inches deep. These should be made up of plank, one and a half or two inches thick, cut into ‘cants,’ one-sixth, eighth, or tenth of the circle, so as to place the grain of the wood as nearly as practicable in the direction of the circumference. The cants should be closely fitted, and put together with white lead or glue, strongly nailed and bolted. The wooden rim, thus made up to within about three inches of the width required for the finished pulley, is mounted upon one or two heavy iron ‘spiders,’ with six or eight radial arms. If the pulley is above six feet in diameter, there should be eight arms, and two spiders when the width of face is more than eighteen inches.
“Upon the ends of the arms are flat ‘pads,’ which should be of just sufficient width to extend across the inner face of the wooden rim, as described; that is, three inches less than the width of the finished pulley. These pads are gained into the inner side of the rim; the gains being cut large enough to admit keys under and beside the pads. When the keys are well driven, strong ‘lag’ screws are put through the ends of the arm into the rim. This done, an additional ‘round’ is put upon each side of the rim to cover bolt heads and secure the keys from ever working out. The pulley is now put to its place on the shaft and keyed, the edges trued up, and the face turned off with the utmost exactness.
“For small drivers, the best construction is to make an iron pulley of about eight inches less diameter and three inches less face than the pulley required. Have four lugs, about an inch square, cast across the face of this pulley. Make a wooden rim, four inches deep, with face equal to that of the iron pulley, and the inside diameter equal to the outer diameter of the iron. Drive this rim snugly on over the rim of the iron pulley having cut gains to receive the lugs, together with a hard wood key beside each. Now add a round of cants upon each side, with their inner diameter less than the first, so as to cover the iron rim. If the pulley is designed for heavy work, the wood should be maple, and should be well fastened by lag screws put through the iron rim; but for light work, it may be of basswood or pine, and the lag screws omitted. But in all cases, the wood should be thoroughly seasoned.
“In the early use of friction-gearing, when it was used only as backing gear in saw-mills, and for hoisting in grist-mills, the pulleys were made so as to present the head of the wood to the surface; and we occasionally yet meet with an instance where they are so made. But such pulleys never run so smoothly nor drive so well as those made with the fibre more nearly in a line with the work.”[11]