MATCHING SET
MATCHING SET No. 7165
MATERIALS:
J. & P. COATS KNIT-CRO-SHEEN.2 balls of a light color and 3 balls of a dark color for runner; 2 balls of a light color and 2 balls of a dark color for chair set.
Milward’s Steel Crochet HookNo. 6 or 7.
GAUGE: 11 dc make 1″; 5 rows make 1″ (1 square is equivalent to 3 dc).
RUNNERNo. 7165-A
Completed runner measures 13″ x 30″ (omitting fringe).
Starting at short side, with dark color make a chain about 15″ long.1st row: Dc in 4th ch from hook, dc in each ch across until there are 141 dc in the row, counting turning ch as 1 dc. Cut off remaining chain. Ch 3, turn.2nd, 3rd and 4th rows: Dc in each dc across. Ch 3, turn. Do not ch 3 to turn at end of 4th row, but leave the last 2 loops of last dc on hook, attach light color and draw through the 2 loops. Ch 3, turn.5th row: Holding dark color at top of previous row and working over it in order to conceal it, make dc in each of 2 dc, leaving the last 2 loops of 2nd dc on hook; * drop light color, pick up dark color, and draw through the 2 loops on hook; then, holding light color at top of previous row and working over it, make dc in each of next 3 dc, leaving the last 2 loops of last dc on hook. Drop dark color, pick up light color and draw through the 2 loops on hook; then, holding dark color at top of previous row and working over it, make dc in each of next 3 dc, leaving last 2 loops on hook. Repeat from * across, ending with 3 light dc. Ch 3, turn.6th row: Dc in each dc across, concealing dark color as before. Hereafter follow chart for runner, beginning at 7th row from bottom and working until 17 rows are completed, concealing unused color as before (count 3 dc for each square). Break off light color and continue with dark color, making dc in each dc across for 3 more rows. Hereafter follow chart, starting at the 21st row from bottom, and work to top of chart, but carry light color only as far as necessary to continue pattern on next row. Then reverse the design by working back to the 1st row. Fasten and break off.
FRINGE...Cut 5 strands of light color, each 10″ long. Double these strands, forming a loop. Pull loop through last dc made, and draw loose ends of fringe through this loop. Pull tight. Make fringe in every 4th dc across short side only. Trim ends evenly. Finish opposite end to correspond.
CHAIR SETNo. 7165-B
Completed chair back measures about 10″ x 16″, and each arm piece about 8″ x 9″, omitting fringe.
CHAIR BACK...Starting at bottom, with dark color make a chain about 18″ long.1st row: Dc in 4th ch from hook, dc in each ch across until there are 171 dc in the row, counting turning ch as 1 dc. Cut off remaining chain. Ch 3, turn.2nd and 3rd rows: Dc in each dc across. Ch 3, turn. Do not ch 3 to turn at end of 3rd row, but leave the last 2 loops of last dc on hook, attach light color and draw through the 2 loops. Ch 3, turn. Hereafter follow chart for chair back, starting at the 4th row from bottom, and work to top of chart, always concealing unused color as in Runner 7165-A.
FRINGE...Make fringe across lower edge of chair back as for Runner 7165-A.
ARM PIECES...Starting at bottom, ch 83 (to measure about 9″), and follow chart for arm piece (working as for chair back). Make fringe at lower edge as for chair back.
CHARTS FOR No. 7165CHART FOR RUNNER, CHART FOR CHAIR BACK, and CHART FOR ARM PIECESfilled box—LIGHTempty box—DARK
CHART FOR RUNNER, CHART FOR CHAIR BACK, and CHART FOR ARM PIECESfilled box—LIGHTempty box—DARK
CHART FOR RUNNER, CHART FOR CHAIR BACK, and CHART FOR ARM PIECESfilled box—LIGHTempty box—DARK