Self-opening Die Heads.—The type of die holder shown atBinFig. 11is objectionable because of the time required for backing the die off the threaded end; hence, self-opening dies are extensively used in turret lathe work. As the name implies,this type of die, instead of being solid, has several chasers which are opened automatically when the thread has been cut to the required length. The turret can then be returned without reversing the lathe spindle. The dies are opened by simply stopping the travel of the turret slide, the stop-rod for the feed of the turret being adjusted to give the proper amount of travel.
Self-opening and Adjustable Screw-cutting Die HeadFig. 13. Geometric Self-opening and Adjustable Screw-cutting Die Head
Self-opening and Adjustable Screw-cutting Die Head
Fig. 13. Geometric Self-opening and Adjustable Screw-cutting Die Head
A well-known die head of the self-opening type is shown inFig. 13. The dies open automatically as soon as the travel of the head is retarded, or they can be opened at any point by simply holding back on the turnstile or lever by which the turret slide is moved. The die is closed again by means of the small handle seen projecting at right-angles from the side of the head. The closing may be done by hand or automatically by screwing a pin into a threaded hole opposite the handle and attaching a small piece of flat steel to the back edge of the turret slide. The latter will then engage the pin as the turret revolves, thus closing the die head. This die head has a roughing and finishing attachment which is operated by handleA. When this handle is moved forward, the dies are adjusted outward 0.01 inch for the roughing cut, whereas returning the handle closes and locks the dies for the finishing cut. The die head has a micrometer scale which is used when making slight adjustments to compensate for the wear of the chasers or to make either a tight-or a loose-fitting thread.
Geometric Collapsing TapFig. 14. Geometric Collapsing Tap
Geometric Collapsing Tap
Fig. 14. Geometric Collapsing Tap
Collapsing Taps.—The collapsing tap shown inFig. 14is one of many different designs that are manufactured. They are often used in turret lathe practice in place of solid taps. When using this particular style of collapsing tap, the adjustable gageAis set for the length of thread required. When the tap has been fed to this depth, the gage comes into contact with the end of the work, which causes the chasers to collapse automatically. The tool is then withdrawn, after which the chasers are again expanded and locked in position by the handle seen at the side of the holder. In all threading operations, whether using taps or dies, a suitable lubricant should be used, as a better thread is obtained and there is less wear on the tools. Lard oil is a good lubricant, although cheaper compounds give satisfactory results on many classes of work.
Various Types of Tools for the Turret LatheFig. 15. Various Types of Tools for the Turret Lathe
Various Types of Tools for the Turret Lathe
Fig. 15. Various Types of Tools for the Turret Lathe
Miscellaneous Turret Lathe Tools.—The chamfering tool shown atA,Fig. 15, is used for pointing the end of a bar before running on a roughing box-tool. This not only finishes the end of the bar but provides an even surface for the box-tool to start on. The cutter is beveled on the end to form a cutting edge and it is held at an angle. The back-rest consists of a bell-mouthed, hardened tool-steel bushing which supports the bar while the cut is being taken.
The stop gagesBandCare used in the turret to govern the length of stock that is fed through the spindle. When a finished piece has been cut off, the rough bar is fed through the spindle and up against the stop gage, thus locating it for another operation. This gage may be a plain cylindrical piece of hardened steel, as atB, or it may have an adjusting screw as atC; for special work, different forms or shapes are also required. The stop gages on some machines, instead of being held in the turret, are attached to a swinging arm or bracket that is fastened to the turret slide and is swung up in line with the spindle when the stock is fed forward.
The center drilling toolDis designed to hold a standard combination center drill and reamer. This type of tool is often used when turning parts that must be finished afterwards by grinding, to form a center for the grinding machine. The adjustable turningtoolEis used for turning the outside of gear blanks, pulley hubs or the rims of small pulleys. The pilotaenters the finished bore to steady the tool, and cutterbis adjusted to turn to the required diameter.
The cutting-off tool-holderF(which is held on the cross-slide of the turret lathe) is usually more convenient than a regular toolpost, as the blade can be set closer to the chuck. The blade is held in an inclined position, as shown, to provide rake for the cutting edge; the inclined blade can also be adjusted vertically, a limited amount, by moving it in or out. The multiple cutting-off toolGholds two or more blades and is used for cutting off several washers, collars, etc., simultaneously. By changing the distance pieces between the cutters, the latter are spaced for work of different widths. The flat drill holderHis used for drilling short holes, and also to form a true “spot” or starting point for other drills.
Knurling tools are shown atIandJ. The former is intended for knurling short lengths and is sometimes clamped on top of the cut-off tool on the cross-slide, the end being swung back after knurling (as shown by the dotted lines) to prevent interference with the work when the cutting-off tool is in operation. The knurling toolJhas a shank and is held in the turret. The two knurls are on opposite sides of the work so that the pressure of knurling is equalized. By adjusting the arms which hold the knurls, the tool can be set for different diameters.
Three styles of drill holders are shown atK,LandM. HolderKis provided with a split collet (seen to the left) which is tightened on the drill shank by a set-screw in the holder. This holder requires a separate collet for each size drill. The taper shank drill holderLhas a standard taper hole into which the shank of the drill is inserted. The adjustable type of holderMis extensively used, especially on small and medium sized machines when several sizes of drills are necessary. This holder is simply a drill chuck fitted with a special shank. For large drills the plain style of holderKis recommended, and if only a few sizes of drills are required, it is more satisfactory and economical than the adjustable type.
The various types of small turret lathe tools referred to in the foregoing for turning, threading, tapping, knurling, etc., are a few of the many different designs of tools used in turret lathe practice. Naturally, the tool equipment for each particular job must be changed somewhat to suit the conditions governing each case. The tools referred to, however, represent in a general way, the principal types used in ordinary practice. Some of the more special tools are shown in connection with examples of turret lathe work, which are referred to in the following.
Method of Boring and Turning Pistons in Gisholt Lathe, Special Chuck and Tools for Turning, Boring and Cutting Off Eccentric Piston RingsFig. 16. (A) Method of Boring and Turning Pistons in Gisholt Lathe.(B) Special Chuck and Tools for Turning, Boring and Cutting Off Eccentric Piston Rings
Method of Boring and Turning Pistons in Gisholt Lathe, Special Chuck and Tools for Turning, Boring and Cutting Off Eccentric Piston Rings
Fig. 16. (A) Method of Boring and Turning Pistons in Gisholt Lathe.(B) Special Chuck and Tools for Turning, Boring and Cutting Off Eccentric Piston Rings
Turning Gasoline Engine Pistons in Turret Lathe.—The making of pistons for gas engines, especially in automobile factories, is done on such a large scale that rapid methods of machining them are necessary. The plan viewA,Fig. 16, shows the turret lathe tools used in one shop for doing this work. Asis often advisable with work done in large quantities, the rough castings are made with extra projections so arranged as to assist in holding them. These projections are, of course, removed when the piece is completed. In this case the piston castingahas a ring about 11/4inch long and a little less in diameter than the piston, at the chucking end. The piston is held in suitable chuck jawsbwhich are tightened against the inside of this ring. The set-screws in these special jaws are then tightened, thus clamping the casting between the points of the screws and the jaws. This method of holding permits the whole exterior of the piston to be turned, since it projects beyond the chuck jaws. This is the object in providing the piston with the projecting ring by which it is held.
The first operation consists in rough-boring the front end of the piston. The double-ended cutternis held in boring-barm, which is, in turn, supported by a drill-holder, clamped to oneof the faces of the turret. This bar is steadied by a bushing in the drill supportcwhich is attached to the carriage, and may be swung into or out of the operating position, as required. After this cut is completed, the turret is revolved half way around and the casting is finish-bored in a similar manner, with double-ended cuttern1held in barm1, the drill support being used as in the previous case. The support is then turned back out of the way to allow the turning tools in the turret toolpost to be used.
The outside of the piston is next rough-turned with toolkin the turret toolpost, which is revolved to bring this cutter into action. The toolpost is then turned to the position shown, and the outside is finish-turned by toolj, which takes a broad shaving cut. The turret tool-holder is again revolved to bring form toollinto position. This tool cuts the grooves for the piston rings. Suitable positive stops are, of course, provided for both the longitudinal and cross movements of the turret toolpost.
In the second operation, the pistonais reversed and held in soft jaws, which are used in place of the hardened jawsbshown in the illustration. These jaws are bored to the outside diameter of the piston, so that when closed, they hold the work true or concentric with the lathe spindle. In this operation the chucking ring by which the piston was previously held is cut off, and the end of the piston is faced true. If the crank-pin hole is to be finished, a third operation is necessary, a self-centering chuck-plate and boring and reaming tools being used. (These are not shown in the illustration.)
Turning Piston Rings in Turret Lathe.—One method of turning piston rings is shown atBinFig. 16. The piston rings are cut from a cast-iron cylindrical piece which has three lugsbcast on one end and so arranged that they may be held in a three-jawed chuck. This cylindrical casting is about 10 inches long, and when the rings are to have their inside and outside surfaces concentric, the casting is held by the lugs in the regular jaws furnished with the chuck. (The arrangement used for turning and boring eccentric rings, which is that shown in the illustration, will be described later.)
The castinga, from which the rings are made, is first rough-bored with double-ended cutternin boring-barm, after which it is finish-bored with cuttern1in barm1. While taking these cuts, the barsmandm1are supported by their extension ends which enter bushingrlocated in the central hole of the chuck. This furnishes a rigid support so that a heavy cut can be taken.
The outside of the casting is next rough-turned with toolk, held in the turret toolpost. This toolpost is then revolved to bring tooljinto position, by which the outside is turned true to size, a broad shaving chip being taken. The toolpost is again swung around, to bring the cutting-off tool-holderlinto position. This holder contains four blades set the proper distance apart to give rings of the desired width. Each blade, from right to left, is set a little back of the preceding one, so that the rings are cut off one after the other, the outer rings being supported until they are completely severed. After the first four rings are cut off, the carriage is moved ahead to a second stop, and four more rings are severed, this operation being continued until the casting has been entirely cut up into rings.
When the bore of the ring is to be eccentric with the outside, the holding arrangement shown in the illustration is used. The casting a is bolted to a sliding chuck-platec, and the outside is rough-turned with toolkin the toolpost. Finishing tooljis then brought into action, and the outside diameter is turned accurately to size. Then the sliding chuck-platec, carrying the work, is moved over a distance equal to the eccentricity desired, and the work is bored with cuttersnandn1as in the previous case. The turret toolpost is next revolved and the toolslare used for cutting off the rings. The reason for finishing the outside first is to secure smooth rings in cutting off, as this operation should be done when the work is running concentric with the bore, rather than with the exterior surface.
It will be evident that this method gives a far greater output of rings than is possible by finishing them in the more primitive way on engine lathes. The faces of the rings may be finished in a second operation if desired, or they may be ground, dependingon the method used in the shop where the work is being done, and the accuracy required.
Turning Gasoline Engine Pistons in Pratt & Whitney Turret LatheFig. 17. Turning Gasoline Engine Pistons in Pratt & Whitney Turret Lathe
Fig. 17. Turning Gasoline Engine Pistons in Pratt & Whitney Turret Lathe
Piston Turning in Pratt and Whitney Turret Lathe.—A turret lathe equipped with tools for turning, facing and grooving automobile gasoline engine pistons is shown inFig. 17. The piston is held on an expanding pin chuck which is so constructed that all of the pins are forced outward with equal pressure and automatically conform to any irregularities on the inside of the piston. ToolArough-turns the outside, and just as this tool completes its cut, a center hole is drilled and reamed in the end of the piston by combination drill and reamerB. The turret is then indexed one-half a revolution and a finishing cut is taken by toolC. After the cylindrical body of the piston has been turned, tools held in a special holderEattached to the cut-off slide are used to face the ends of the piston and cut the packing-ring grooves. While the grooves are being cut, the outer end of the piston is supported by centerD. The center hole in the end also serves to support the piston while being ground to the required diameter in a cylindrical grinding machine. The edge at the open end of the piston may also be faced square andthe inner corner beveled by a hook tool mounted on the rear cross-slide, although this is usually done in a separate operation. (This provides a true surface by which to hold this end when grinding.)
This illustration (Fig. 17) shows very clearly the stops which automatically disengage the turret feed. A bracketFis bolted to the front of the bed and contains six stop-rodsG(one for each position or side of the turret). When one of these stop-rods strikes leverH, the feed is disengaged, the stop being adjusted to throw out the feed when the tool has completed its cut. LeverHis automatically aligned with the stop-rods for different sides of the turret by a camJon the turret base. A rollerKbears against this cam and, through the connecting shaft and lever shown, causes leverHto move opposite the stop-rod for whatever turret face is in the working position. LeverLis used for engaging the feed and leverRfor disengaging it by hand.
The indexing of the turret at the end of the backward movement of the slide is controlled by stopMagainst which rodNstrikes, thus disengaging the lock bolt so that the turret can turn. This stopMis adjusted along the bed to a position depending upon the length of the turret tools and the distance the turret must move back to allow the tools to clear as they swing around.
Pratt & Whitney Turret Lathe equipped with Special Attachment for Turning Eccentric Piston RingsFig. 18. Pratt & Whitney Turret Lathe equipped with SpecialAttachment for Turning Eccentric Piston Rings
Fig. 18. Pratt & Whitney Turret Lathe equipped with SpecialAttachment for Turning Eccentric Piston Rings
Attachment for Turning Piston Rings.—Fig. 18shows a special attachment applied to a Pratt & Whitney turret lathe for turning eccentric, gas-engine piston rings. The boring of the ring casting, turning the outside and cutting off the rings, is done simultaneously. The interior of the casting is turned concentric with the lathe spindle by a heavy boring-bar, the end of which is rigidly supported by a bushing in the spindle. The slide which carries the outside turning tool is mounted on a heavy casting which straddles the turret. The outside of the ring casting is turned eccentric to the bore as a result of an in-and-out movement imparted to the tool by a cam on shaftAwhich is rotated from the lathe spindle through the gearing shown. For each revolution of the work, the tool recedes from the center and advances toward it an amount sufficient to givethe required eccentricity. When the turning and boring tools have fed forward about 2 inches, then the cutting-off tools which are held in holderBcome into action. The end of each cutting-off tool, from right to left, is set a little farther away from the work than the preceding tool, so that the end rings are always severed first as the tools are fed in by the cross-slide. A number of the completed rings may be seen in the pan of the machine.
Tool Equipment for Worm Gear Blanks—Davis Turret LatheFig. 19. Tool Equipment for Machining Worm Gear Blanks—Davis Turret Lathe
Fig. 19. Tool Equipment for Machining Worm Gear Blanks—Davis Turret Lathe
Turning Worm-gear Blanks in Turret Lathe.—This is a second operation, the hub of worm-gear blankG(Fig. 19) having previously been bored, reamed, and faced on the rear side. The casting is mounted upon a close-fitting arbor attached to a plate bolted to the faceplate of the lathe, and is driven by two pins which engage holes on the rear side. The rim is first rough-turned by a toolAwhich operates on top, and the side is rough-faced by a toothed or serrated cutterB. A similar tool-holderhaving a toolCand a smooth cutterDis then used to turn the rim to the required diameter and finish the side. The end of the hub is faced by cutters mounted in the end of barsEandF, one being the roughing cutter and the other the finishing cutter. The work arbor projects beyond the hub, as will be seen, and forms a pilot that steadies these cutter bars. The curved rim of the gear is turned to the required radius (preparatory to gashing and bobbing the worm-wheel teeth) by a formed toolHheld on the cross-slide.
Turning Bevel Gear Blanks in Davis Turret Lathe—First OperationFig. 20. Turning Bevel Gear Blanks in Davis Turret Lathe—First Operation
Fig. 20. Turning Bevel Gear Blanks in Davis Turret Lathe—First Operation
Turning Bevel Gear Blanks.—Fig. 20shows a plan view of the tools used for the first turning operation on bevel gear blanks (these gears are used for driving drill press spindles). The cored hole is beveled true at the end by flat drillAto form a true starting surface for the three-fluted drillBwhich follows. The hole is bored close to the required size by a tool (not shown) held in the end of barC, and it is finished by reamerD. The cylindrical end of the gear blank or hub is rough-and finish-turned bytools held in holdersEandF, respectively. (These holders were made to set at an angle of 45 degrees, instead of being directly over the work, as usual, so that the cutters would be in view when setting up the machine.) It will be noted that the chuck is equipped with special jaws which fit the beveled part of the casting.
Second Operation on Bevel Gear BlanksFig. 21. Second Operation on Bevel Gear Blanks
Fig. 21. Second Operation on Bevel Gear Blanks
The second and final operation on this blank is shown inFig. 21. The workAis held by a special driver plate attached to the faceplate of the machine. This driver plate has two pins which engage holes drilled in the gear blank and prevent it from rotating. The blank is also held by a boltBwhich forces a bushing against the cylindrical end. First, the broad beveled side which is to be the toothed part of the gear, is rough-turned by toothed cuttersC, and a recess is formed in the end of the blank, by a turning tool in this same tool-holder. A similar tool-holderE, having finishing cutters, is then used to finish the bevel face and recess. The other tools seen in the turret are not used for this second operation. The rear bevel is roughed and finished by tools and held on the cross-slide.
Shell Turning Operation in Flat Turret Lathe.—The “flat turret lathe” is so named because the turret is a flat circular plate mounted on a low carriage to secure direct and rigid support from the lathe bed. The tools, instead of being held byshanks inserted in holes in the turret, are designed so that they can be clamped firmly onto the low circular turret plate.
Sectional View of Tapering Mold Shell which is turned in Hartness Flat Turret LatheFig. 22. Sectional View of Tapering Mold Shell which is turned inHartness Flat Turret Lathe, as illustrated inFigs. 23to27, Inclusive
Sectional View of Tapering Mold Shell which is turned in Hartness Flat Turret Lathe
Fig. 22. Sectional View of Tapering Mold Shell which is turned inHartness Flat Turret Lathe, as illustrated inFigs. 23to27, Inclusive
An interesting example of flat turret lathe work is shown inFig. 22. This is a steel shell which must be accurately finished to a slight taper, both inside and out, threaded and plain recesses are required at the ends, and, in addition, one or two minor operations are necessary. This work is done in the Hartness flat turret lathe, built by the Jones & Lamson Machine Co. The shells are turned from cold-drawn seamless steel tubing, having a carbon content of 0.20 per cent, and they are finished at the rate of one in nine minutes. The tubing comes to the machine in 12-foot lengths, and the tube being operated upon is, of course, fed forward through the hollow spindle as each successive shell is severed.
Rough-turning and BoringFig. 23. First Operation on Shell Illustrated inFig. 22—Rough-turning and Boring
Fig. 23. First Operation on Shell Illustrated inFig. 22—Rough-turning and Boring
In finishing this shell, five different operations are required. During the first operation the shell is rough-bored and turned by one passage of a box-tool,Fig. 23, and the recessA,Fig. 22, at the outer end, is finished to size by a second cutter located in the boring-bar close to the turret. The turret is then indexed to the second station which brings the threading attachmentGinto position, as shown inFig. 24. After the thread is finished,the recessB,Fig. 22, is turned by a flat cutterK,Fig. 25. The inner and outer surfaces are then finished to size by a box-tool mounted on the fourth station of the turret and shown in position inFig. 26. The final operation,Fig. 27, is performed by three tools held on an auxiliary turret cross-slide, and consists in rounding the corners atbandc,Fig. 22, and severing the finished shell.
One of the interesting features connected with the machining of this shell is the finishing of the inner and outer tapering surfaces. The taper on the outside is3/32inch per foot, while the bore has a taper of only1/64inch per foot, and these surfaces are finished simultaneously. The box-tool employed is of a standard type, with the exception of an inserted boring-bar, and the taper on the outside is obtained by the regular attachment which consists of a templetD(Fig. 23) of the required taper, that causes the turning tool to recede at a uniform rate as it feeds along. To secure the internal taper, the headstock of the machine is swiveled slightly on its transverse ways by the use of tapering gibs. By this simple method, the double taper is finished to the required accuracy without special tools or equipment.
Cutting Internal ThreadFig. 24. Second Operation—Cutting Internal Thread
Fig. 24. Second Operation—Cutting Internal Thread
Turning Recess at Rear End; Tool is shown withdrawnFig. 25. Third Operation—Turning Recess at Rear End; Tool is shown withdrawn
Fig. 25. Third Operation—Turning Recess at Rear End; Tool is shown withdrawn
Finishing the Bore and OutsideFig. 26. Fourth Operation—Finishing the Bore and Outside
Fig. 26. Fourth Operation—Finishing the Bore and Outside
Rounding Ends, Scoring Large End, and Cutting OffFig. 27. Fifth Operation—Rounding Ends, Scoring Large End, and Cutting Off
Fig. 27. Fifth Operation—Rounding Ends, Scoring Large End, and Cutting Off
As those familiar with this machine know, the longitudinalmovements of the turret as well as the transverse movements of the headstock are controlled by positive stops. The headstock of this machine has ten stops which are mounted in a revolving holder and are brought into position, as required, by manipulating a lever at the front. The stops for length, or those controlling the turret travel, are divided into two general groups, known as “A” and “B”. Each of these groups has six stops so that there are two stops for each of the six positions or stations of the turret, and, in addition, five extra stops are available for any one tool, by the engagement of a pin at the rear of the turret. The change from the “A” to the “B” stops is made by adjusting leverL,Fig. 26, which also has a neutral position.
After the box-tool for the roughing cut, shown at work inFig. 23, has reached the end of its travel, further movement is arrested by a stop of the “A” group. The outside turning tool is then withdrawn by operating leverEand the turret is run back and indexed to the second station, thus bringing the threading attachment into position. The surface speed of 130 feet per minute which is used for turning is reduced to about 30 feet per minute for threading by manipulating leversH,Fig. 24. After the turret is located by another stop of the “A” group, thethreading attachment is made operative by depressing a small plungerI, which connects a vertical driving shaft from the spindle with the splined transmission shaftJ. A reciprocating movement is then imparted to the thread chasertwhich advances on the cutting stroke and then automatically retreats to clear the thread on the return. This movement is repeated until the thread is cut to the proper depth, as determined by one of the stops for the headstock. While the thread is being cut, the carriage is locked to the bed by the leverN,Fig. 26. It was found necessary to perform the threading operation before taking the outside finishing cut, owing to a slight distortion of the shell wall, caused by the threading operation.
After the thread is finished, the turret is turned to the third station as shown inFig. 25, and toolKfor the inner recessB,Fig. 22, is brought into position and fed to the proper depth, as determined by another cross-stop. The turret is also locked in position for this operation. The finishing cuts for the bore and the outside are next taken by a box-tool which is shown near the end of its cut inFig. 26. This box-tool is similar to the one used for roughing, but it is equipped with differently shaped cutters to obtain the required finish. The outside turningtool has a straight cutting edge set tangent to the cylindrical surface and at an angle, while the boring tool has a cutting edge of large radius. An end view of this box-tool is shown inFig. 27. A reduced feed is employed for the finishing cut, and the speed is increased to 130 feet per minute, which is the same as that used for roughing.
During the next and final operation, the turret, after being indexed to the position shown inFig. 27, is first located by a stop of the “A” group so that the cutting-off toolRin front can be used for rounding the cornerb,Fig. 22. The stop leverLis then shifted and the turret is moved to a second stop of the “B” group. The cornercis then rounded and the shell is scored atdby two inverted toolsSandTat the rear, after which the finished work is severed by the cut-off tool at the front. The cross-movement of these three tools is controlled by positive stops on the cross-slide, and the latter is moved to and fro by hand leverO. After the shell is cut off, the stopM, mounted on the turret,Fig. 26, is swung into position, and the tube is automatically fed forward to the swinging stop by the roll feed, as soon as the chuck is released by operating leverQ. This completes the cycle of operations. A copious supply of lubricantis, of course, furnished to the tools during these operations, and the two boring-tool shanks are hollow so that lubricant can be forced through them and be made to play directly upon the cutters.
Tool Equipment for Turning Scroll Gear Blank on Acme Flat Turret LatheFig. 28. Tool Equipment for Turning Scroll Gear Blank on Acme Flat Turret Lathe
Fig. 28. Tool Equipment for Turning Scroll Gear Blank on Acme Flat Turret Lathe
Chuck Work in Flat Turret Lathe.—Two examples of chuck work on the Acme combination flat turret lathe are shown inFigs. 28and29.Fig. 28shows the tool equipment for turning a cylindrical partAwhich is held in a three-jaw universal chuck. The front flange is first rough-turned by a bent turning toolB. The diameter is regulated by one of the cross-stops atDwhich has been previously set and controls the movement of the turret cross-slide. The longitudinal feed is disengaged when the flange has been turned, by an independent stop. This machine has twelve longitudinal stops, there being one for each turret face and six auxiliary stops, in addition to the stops for the cross-slide.
After roughing the flange, the turret carriage is locked or clamped rigidly to the bed to prevent any lengthwise movement, and the back face of the front flange is rough-turned by toolBin to the diameter of the hub which is indicated by a micrometer dial on the cross-feed screw. The carriage is then unlocked and auxiliary stop No. 7 is engaged (by turning a knob at the front of the slide) and the cylindrical hub is turned back to the rear flange, the feed being disengaged by the auxiliary stop just as the tool reaches the flange. The cross-slide is now moved outward, longitudinal auxiliary stop No. 8 is engaged, the turret slide is moved against the stop, the carriage is locked and the front sides of both the front and rear flanges are rough-faced by toolsBandC. The turret is next indexed and the hole rough-bored by cutterE. After again indexing the turret, the hub and flanges are finish-turned and faced by toolsFandG, as described for the rough-turning operation. The final operation is that of finishing the bore by cutterH.
Acme Flat Turret Lathe Arranged for Turning Roller Feed BodyFig. 29. Acme Flat Turret Lathe Arranged for Turning Roller Feed Body
Fig. 29. Acme Flat Turret Lathe Arranged for Turning Roller Feed Body
The operation shown inFig. 29is that of turning the body of a roller feed mechanism for a turret lathe. The casting is held in a three-jaw universal chuck and it is first rough-bored by toolA. The turret is then indexed and the side of the body and end of the hub are rough-faced by tools atB. The turret is again indexed for rough-turning the outside of the hub andbody, by toolsCandD. Similar toolsEandFare then used to finish these same surfaces, after which the end of the hub and side of the body are finished by toolsGandHsimilar to those located atB. The final operation is that of finishing the bore by toolJand cutting a groove in the outside of the hub by the bent toolK.
Turret and Head of Jones & Lamson Double-spindle Flat Turret LatheFig. 30. Turret and Head of Jones & Lamson Double-spindle Flat Turret Lathe
Fig. 30. Turret and Head of Jones & Lamson Double-spindle Flat Turret Lathe
Double-spindle Flat Turret Lathe.—The extent to which modern turning machines have been developed, especially for turning duplicate parts in quantity, is illustrated by the design of turret lathe the turret and head of which is shown inFig. 30. This machine has two spindles and a large flat turret which holds a double set of tools, so that two duplicate castings or forgings can be turned at the same time. It was designed primarily for chuck work and can be used as a single-spindle machine if desirable. When two spindles are employed for machining two duplicate parts simultaneously, considerably more time is required for setting up the machine than is necessary for the regular single-spindle type, but it is claimed that the increased rate of production obtained with the two-spindle design more than offsetsthis initial handicap. The manufacturers consider the single-spindle machine the best type for ordinary machine building operations, regardless of whether the work is turned from the bar or is of the chucking variety. On the other hand, the double-spindle type is preferred when work is to be produced in such quantities that the time for setting up the machine becomes a secondary consideration.
When the double-spindle machine is used as a single-spindle type, a chuck 17 inches in diameter is used, and when both spindles are in operation, two 9-inch chucks are employed. The general outline of the turret is square, and the tools are rigidly held, with a minimum amount of overhang, by means of tool-blocks and binding screws connected with the clamping plates. Two duplicate sets of tools are clamped to each side of the turret and these operate simultaneously on the two pieces held in the chucks or on faceplates. Primarily the turret is usedin but four positions, but when a 17-inch chuck or faceplate is employed, corner blocks may be held by the clamping plates in which tools are supported, giving, if necessary, four additional operations by indexing the turret to eight positions.
Diagram showing Tool Equipment and Successive Steps in Machining Sprocket Blanks on Double-spindle Flat Turret LatheFig. 31. Diagram showing Tool Equipment and Successive Stepsin Machining Sprocket Blanks on Double-spindle Flat Turret Lathe
Diagram showing Tool Equipment and Successive Steps in Machining Sprocket Blanks on Double-spindle Flat Turret Lathe
Fig. 31. Diagram showing Tool Equipment and Successive Stepsin Machining Sprocket Blanks on Double-spindle Flat Turret Lathe
A typical job to demonstrate the application of the double-spindle flat turret lathe is illustrated inFig. 31. The parts to be turned are sprocket wheels which are held in the two 9-inch chucks. At the first position of the turret (which is the one illustrated), the inside is rough-bored by toolsA. At the second position of the turret, toolsBrough-face the inner sides of the flanges; toolsCface the outer sides of the flanges, while toolsDturn the faces of the flanges. At the third position of the turret, toolsEfinish-turn the inside of the flanges; toolsFfinish-turn the outside of the flanges, while toolsGfinish the faces of the flanges. At the fourth position of the turret, toolsHfinish-bore the sprockets; toolsIcomplete the turning on the outside of the flanges, while toolsJaccurately size the interior of the flanges.
With the double-spindle flat turret lathe, each operation is a double operation, and the speeds are varied according to the nature of the cut; thus, if at one position of the turret, the tools are required to rough out the work, this may be done rapidly, for it has no bearing on the other operations that are subsequently performed. Furthermore, if the following operation has to be performed with great care, this may be done without reducing the speed of the less exacting operations.
Potter & Johnston MachineFig. 32. Potter & Johnston Automatic Chucking and Turning Machine
Fig. 32. Potter & Johnston Automatic Chucking and Turning Machine